IEI Technology IMB-H110 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 161

background image

IMB-H110 microATX Motherboard

Page 122

5.5 Security

Use the

Security

menu (

BIOS Menu 29

) to set system and user passwords.

Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc.

Main

Advanced

Chipset

Security

Boot

Save & Exit

Password Description

If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup.
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password length must be:
Minimum length

3

Maximum length

20

Administrator Password
User Password

Set Administrator
Password

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

Version 2.17.1255. Copyright (C) 2016 American Megatrends, Inc.

BIOS Menu 29: Security

Î

Administrator Password

Use the

Administrator Password

to set or change a administrator password.

Î

User Password

Use the

User Password

to set or change a user password.

«
...
135
136
137
138
139
...
»

Содержание IMB-H110


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMB-H110

Бренд: Yamaha Страницы: 96

Бренд: AOpen Страницы: 101

Бренд: Avalue Technology Страницы: 12

Бренд: MIPS Страницы: 10

Бренд: NXP Semiconductors Страницы: 14

Бренд: ST Страницы: 79

Бренд: MaxLinear Страницы: 25

Бренд: MSI Страницы: 169

Бренд: Texas Instruments Страницы: 18

Бренд: Ublox Страницы: 42

Бренд: ASROCK Страницы: 26

Бренд: ASROCK Страницы: 26

Бренд: Texas Instruments Страницы: 51

Бренд: Texas Instruments Страницы: 44

Бренд: ITX SECURITY Страницы: 18

Бренд: Intel Страницы: 36

Бренд: Renesas Страницы: 2

Бренд: JETWAY Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды