IEI Technology IMB-H110 Скачать руководство пользователя страница 128

Страница: 128 / 161

IMB-H110 microATX Motherboard

Page 113

5.4.1.1 Graphics Configuration

Use the

Graphics Configuration

(

BIOS Menu 22

) menu to configure the video device

connected to the system.

Chipset

Graphics Configuration

Primary Display

[Auto]

DVMT Pre-Allocated

[256M]

DVMT Total Gfx Mem

[MAX]

Primary IGFX Boot Display

[VBIOS Default]

Backlight Control Mode

[LED(PWM)]

Backlight Control Type

[PWM]

Select which of
IGFX/PEG/PCI Graphics
device should be Primary
Display Or select SG for
Switchable Gfx.

----------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized Defaults
F4: Save & Exit
ESC: Exit

BIOS Menu 22: Graphics Configuration

Primary Display [Auto]

Use the

Primary Display

option to select the primary graphics controller the system uses.

The following options are available:

Auto

Default

IGFX

PEG

PCIE

DVMT Pre-Allocated [256M]

Use the

DVMT Pre-Allocated

option to set the amount of system memory allocated to the

integrated graphics processor when the system boots. The system memory allocated can

then only be used as graphics memory, and is no longer available to applications or the

operating system. Configuration options are listed below:

32M

64M

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды