IEI Technology IMB-H110 Скачать руководство пользователя страница 75

Страница: 75 / 161

IMB-H110 microATX Motherboard

Page 60

Figure 4-2: Remove Protective Cover

Step 3:

Inspect the CPU socket.

Make sure there are no bent pins and make sure the

socket contacts are free of foreign material. If any debris is found, remove it with

compressed air.

Step 4:

Orientate the CPU properly.

The contact array should be facing the CPU

socket.

WARNING:

DO NOT touch the pins at the bottom of the CPU. When handling the

CPU, only hold it on the sides.

Step 5:

Correctly position the CPU.

Match the Pin 1 mark with the cut edge on the

CPU socket.

Step 6:

Align the CPU pins.

Locate pin 1 and the two orientation notches on the CPU.

Carefully match the two orientation notches on the CPU with the socket

alignment keys.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды