IEI Technology IMB-H110 Скачать руководство пользователя страница 139

Страница: 139 / 161

IMB-H110 microATX Motherboard

Page 124

Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.

Disabled

Normal POST messages displayed

Enabled D

EFAULT

OEM Logo displayed instead of POST messages

Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.

Disabled D

EFAULT

Ignore all PXE Option ROMs

Enabled

Load PXE Option ROMs.

Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.

Force

BIOS

EFAULT

Sets display mode to force BIOS.

Keep

Current

Sets display mode to current.

UEFI Boot [Disabled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.

Enabled

Boot from UEFI devices is enabled.

Disabled D

EFAULT

Boot from UEFI devices is disabled.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды