IEI Technology IMB-H110 Скачать руководство пользователя страница 94

Страница: 94 / 161

IMB-H110 microATX Motherboard

Page 79

Step 8:

Wait for the process to finish. It may take up to 15 minutes.

Figure 4-24: Update Process is Complete

Step 9:

Now the user can proceed with the Windows 7 installation using the updated

installer.

Step 0:

4.11 Driver Installation

All the drivers for the IMB-H110 are on the CD that came with the system. To install the

drivers, please follow the steps below.

NOTE:

The content of the CD may vary throughout the life cycle of the product

and is subject to change without prior notice. Visit the IEI website or

contact technical support for the latest updates.

Step 1:

Insert the CD into a CD drive connected to the system.

NOTE:

If the installation program doesn't start automatically:

Click "Start->My Computer->CD Drive->autorun.exe"

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды