IEI Technology IMB-H110 Скачать руководство пользователя страница 123

Страница: 123 / 161

IMB-H110 microATX Motherboard

Page 108

SATA Controller(s) [Enabled]

Use the

SATA Controller(s)

option to configure the SATA controller(s).

Enabled D

EFAULT

Enables the on-board SATA controller(s).

Disabled

Disables the on-board SATA controller(s).

SATA Mode Selection [AHCI]

Use the

SATA Mode Selection

option to determine how the SATA devices operate.

AHCI

EFAULT

Configures SATA devices as AHCI device.

RAID

Configures SATA devices as RAID device.

Hot Plug [Disabled]

Use the

Hot Plug

option to designate the correspondent SATA port as hot-pluggable.

Disabled D

EFAULT

Disables the hot-pluggable function of the SATA port.

Enabled

Designates the SATA port as hot-pluggable.

5.3.10 NVMe Configuration

Use the

NVMe Configuration

(

BIOS Menu 17

) menu to display the NVMe controller and

device information.

Advanced

NVMe controller and Drive information

No NVMe Device Found

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 17:

NVMe Configuration

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды