IEI Technology IMB-H110 Скачать руководство пользователя страница 130

Страница: 130 / 161

IMB-H110 microATX Motherboard

Page 115

5.4.1.2 PEG Port Configuration

Chipset

PEG Port Configuration

PEG 0:1:0

Not Present

Enable Root Port

[Enabled]

Max Link Speed

[Auto]

Detect Non-Compliance Device

[Disabled]

Enable or Disable the
Root Port

----------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized Defaults
F4: Save & Exit
ESC: Exit

BIOS Menu 23: PEG Port Configuration

Enable Root Port [Enabled]

Use the

Enable

Root Port

option to enable or disable the PCI Express (PEG) controller.

Disabled

Disables the PCI Express (PEG) controller.

Enabled D

EFAULT

Enables the PCI Express (PEG) controller.

Max Link Speed [Auto]

Use the

Max Link Speed

option to select the maximum link speed of the PCI Express slot.

The following options are available:

Auto

Default

Gen1

Gen2

Gen3

Detect Non-Compliance Device [Disabled]

Use the

Detect Non-Compliance Device

option to enable or disable detecting if a

non-compliance PCI Express device is connected to the PCI Express slot.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды