IEI Technology IMB-H110 Скачать руководство пользователя страница 98

Страница: 98 / 161

IMB-H110 microATX Motherboard

Page 83

Key

Function

Esc

Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu -- Exit

current page and return to Main Menu

General help, only for Status Page Setup Menu and Option Page

Setup Menu

Load previous values

Load optimized defaults

Save changes and Exit BIOS

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When

is pressed, a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window, press

5.1.4 Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS

defaults. Use the clear CMOS button described in

Chapter

5.1.5 BIOS Menu Bar

The

menu bar

on top of the BIOS screen has the following main items:

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

Chipset – Changes the chipset settings.

Security – Sets User and Supervisor Passwords.

Boot – Changes the system boot configuration.

Save & Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu

items at the top of the BIOS screen and listed above.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды