IEI Technology IMB-H110 Скачать руководство пользователя страница 73

Страница: 73 / 161

IMB-H110 microATX Motherboard

Page 58

WARNING:

The installation instructions described in this manual should be

carefully followed in order to prevent damage to the components and

injury to the user.

Before and during the installation please

the following:

Read the user manual:

The user manual provides a complete description of the IMB-H110

installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD):

Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.

Place the IMB-H110 on an anti-static pad:

When installing or configuring the motherboard, place it on an anti-static

pad. This helps to prevent potential ESD damage.

Turn all power to the IMB-H110 off:

When working with the IMB-H110, make sure that it is disconnected from

all power supplies and that no electricity is being fed into the system.

Before and during the installation of the IMB-H110,

DO NOT:

Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

Use the product before verifying all the cables and power connectors are

properly connected.

Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды