IEI Technology IMB-H110 Скачать руководство пользователя страница 122

Страница: 122 / 161

IMB-H110 microATX Motherboard

Page 107

Intel Virtualization Technology [Disabled]

Use the

Intel Virtualization Technology

option to enable or disable virtualization on the

system. When combined with third party software, Intel® Virtualization technology allows

several OSs to run on the same system at the same time.

Disabled D

EFAULT

Disables Intel Virtualization Technology.

Enabled

Enables Intel Virtualization Technology.

Intel(R) SpeedStep(tm) [Enabled]

Use the

Intel(R) SpeedStep(tm)

option to enable or disable the Intel® SpeedStep

Technology which allows more than two frequency ranges to be supported.

Disabled

Disables Intel® SpeedStep Technology

Enabled D

EFAULT

Enables Intel® SpeedStep Technology

5.3.9 SATA Configuration

Use the

SATA Configuration

menu (

BIOS Menu 16

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced

SATA Controller(s)

[Enabled]

SATA Mode Selection

[AHCI]

SATA1

Empty

Hot Plug

[Disabled]

SATA2

Empty

Hot Plug

[Disabled]

SATA3

Empty

Hot Plug

[Disabled]

SATA4

Empty

Hot Plug

[Disabled]

Enable or disable SATA
Device.

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 16: SATA

Configuration

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды