IEI Technology IMB-H110 Скачать руководство пользователя страница 121

Страница: 121 / 161

IMB-H110 microATX Motherboard

Page 106

Advanced

CPU Configuration

Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz
CPU Signature

506E3

Microcode Patch

Max CPU Speed

3700 MHz

Min CPU Speed

800 MHz

CPU Speed

3700 MHz

Processor Cores

Hyper Threading Technology

Supported

Intel VT-x Technology

Supported

Intel SMX Technology

Not Supported

64-bit Supported
EIST Technology

Supported

L1 Data Cache

32 kB x 2

L1 Code Cache

32 kB x 2

L2 Cache

256 kB x 2

L3 Cache

3 MB

Hyper-threading [Enabled]
Active Processor Cores

[All]

Intel Virtualization Technology [Disabled]
Intel(R) SpeedStep(tm)

[Enabled]

Number of cores to enable
in each processor
package.

----------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 15: CPU Configuration

Hyper-threading [Enabled]

Use the

Hyper-threading

BIOS option to enable or disable the Intel Hyper-Threading

Technology.

Disabled

Disables the Intel Hyper-Threading Technology.

Enabled D

EFAULT

Enables the Intel Hyper-Threading Technology.

Active Processor Cores [All]

Use the

Active Processor Cores

BIOS option to enable numbers of cores in the

processor package.

All

EFAULT

Enable all cores in the processor package.

Enable one core in the processor package.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды