IBM 2109 - SAN Fibre Channel Switch Model S16 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 178

background image

CAUTION:
The controller card contains a lithium battery. To avoid possible explosion, do
not burn, exchange, or charge the battery. Discard the controller card as
instructed by local regulations for lithium batteries. (RSFTC228)

There are no user-serviceable parts inside the power supply chassis. Opening the
power supply voids its warranty and certification.

Note: If this is a dual power machine, you do not need to turn off power to the

good power supply. If the second power supply option is available, turning it
off will disrupt any on-going switch operation.

Tools that are required

None.

Removing a power supply

1. Turn off power to the power supply being replaced. Figure 17 shows the Telnet

error messages that are generated when a power supply is turned off, removed,
replaced, and turned back on. Note that this is normal operation.

2. Remove any external cabling attached to the power supply.

3. Pull out and lift up the handle from the top of the power supply unit. The handle

is shown in Figure 18 on page 47.

4. Gently pull the unit out.

(Old Power Supply turned off)
0x10fc1bb0 (tSwitch) : Mar 10 15:22:54

Error POWER-1_FAILED, 1, Power Supply #1 failed

(Old Power Supply removed)
0x10fc1bb0 (tSwitch) : Mar 10 15:23:08

Error POWER-OK, 4 Power OK

(New Power Supply installed)
0x10fc1bb0 (tSwitch : Mar 10 15:23:16

Error POWER-1_FAILED, 1, Power Supply #1 failed

(New Power Supply turned on)
0x10fc1bb0 (tSwitch) : Mar 10 15:23:27

Figure 17. Generated Telnet messages when a power supply is turned off and removed

46

IBM SAN Fibre Channel Switch: 2109 Model S16 Installation and Service Guide

«
...
60
61
62
63
64
...
»

Содержание 2109 - SAN Fibre Channel Switch Model S16



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2109 - SAN Fibre Channel Switch Model S16

Бренд: La Toulousaine Страницы: 6

Бренд: GE Страницы: 36

Бренд: GE Страницы: 8

Бренд: OFFICINE OROBICHE Страницы: 7

Бренд: Quick Страницы: 28

MMAC-Plus 9H423-26

Бренд: Cabletron Systems Страницы: 14

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Omron Страницы: 16

Бренд: Aethra Страницы: 1

Бренд: Kramer Страницы: 17

Бренд: Metrix Страницы: 12

Бренд: Comtrend Corporation Страницы: 2

Бренд: TAXON TOOLS Страницы: 9

S5120-EI Series

Бренд: H3C Страницы: 29

Antenna-Disconnect-Switch

Бренд: ADS Страницы: 12

Cutler-Hammer RTHMFDA20100WSU

Бренд: Eaton Страницы: 28

TM-1-8290/E/SVB

Бренд: Eaton Страницы: 2

Бренд: Lantech Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды