Hughes HX90 Скачать руководство пользователя страница 96

Страница: 96 / 124

Chapter 8 • Troubleshooting

1039456-0001 Revision A

3. Observe the message in the

Web Acceleration Status

field.

If the Web Acceleration Status is Operational, Web Acceleration is enabled.
Proceed to

Confirming NOC connectivity

on page 97.

Note:

Web Acceleration Status may be

Operational

Inactive

during

normal operation. Connecting does not indicate a problem unless it
persists for more than a few seconds.

4. If the Web Acceleration Status is

Not operational

, Web Acceleration Status

is disabled. Follow these steps:
a. Make sure the router is transmitting and receiving. See

Confirming the receive

signal

on page 93 and

Confirming the transmit signal

on page 93. If necessary,

troubleshoot as stated in these sections.

b. Wait 2 hr.

5. If Web acceleration is still disabled, restart the router:

a. Go to the System Control Center home page.
b. In the Help section, click

Restart HX90

6. If Web acceleration is still disabled, power cycle the router:

a. Unplug the power cord from the power source.
b.

If the router is connected to a DC power source

, unplug the DC input cable

from the satellite router’s power supply.

c. Wait 10 sec.
d. Plug the power cord back into the power source.
e.

If the power source is DC

, plug the input cable back into the power supply.

Do not power cycle the satellite router by unplugging the power cord from the
router’s rear panel. Doing so could result in static electricity discharge that could
shock you and/or damage the router.

7. Check the

Web Acceleration Status

field again.

If Web Acceleration is still not operational, contact your service provider for
assistance.

CAUTION

Содержание HX90





























































































































Результаты поиска

Содержание HX90

Отзывы:

Hughes HX90, Руководство по установке, Страница: 96 / 124

Результаты поиска

Содержание HX90

Отзывы: