manualshive.com logo in svg

Hughes HX90, Руководство по установке, Страница: 101 / 124

Поделиться
Скачать
Hughes HX90 Скачать руководство пользователя страница 101

Chapter 8 • Troubleshooting

 

1039456-0001  Revision A

101

This temporarily bypasses the Ethernet device as a way to help determine where 
and what the problem is.

3. Power cycle the satellite router:

a. Unplug the power cord from the power source.
b.

If the router is connected to a DC power source,

 unplug the DC input cable 

from the satellite router’s power supply.

c. Wait 10 sec.
d. Plug the power cord back into the power source.
e.

If the power source is DC, 

plug the input cable back into the power supply. 

Do not power cycle the satellite router by unplugging the power cord from the 
router’s rear panel. Doing so could result in static electricity discharge that could 
shock you and/or damage the router.

4. Attempt to access the System Control Center by completing the steps in 

Satellite 

router connected directly to a computer

 on page 100.

5. If you cannot access the System Control Center, restart the computer.
6. Try again to access the System Control Center.

If you still 

cannot

 access the System Control Center, contact your service provider.

If you can now access the System Control Center, your Ethernet device may not be 
properly configured. Refer to the documentation for your Ethernet device to 
configure it properly. Be sure to re-connect the satellite router to the Ethernet device 
before attempting to access the System Control Center.

Using the front panel LEDs for troubleshooting

This section explains how to use the satellite router's front panel LEDs to recognize 
and troubleshoot problems.

Before proceeding, make sure the transmit and receive cables are securely 
tightened. 

•

Make sure each connector is properly aligned (not cross-threaded).

•

Finger tight with no connector play is adequate.

Note:  

The router may operate correctly when first installed even if the transmit and 

receive cable connectors are not adequately tightened. However, problems 
could develop later. Therefore, correct operation of the satellite router's is not 
an indication that the cables are adequately tightened.

CAUTION

NOTICE

Содержание HX90





























































































































Отзывы:

Нет отзывов