Hughes HX90 Скачать руководство пользователя страница 82

Страница: 82 / 124

Chapter 6 • System control center

1039456-0001 Revision A

System Information page

The System Information page shown in Figure 64 provides system information for the
satellite router such as Site ID and the release number of the router's operational
software.

Figure 64: System Information page

The parameters listed in the

HX90 Info

section of the System Information page are

explained in the following table. Other sections of the screen (

Transmit Radio Info

and

Satellite

) provide additional information about the router installation and the

router software (Software Configuration).

Table 9: System Information page parameters — HX90 Info section

Parameter

Explanation

Site ID

Identifies the site where the router is installed.

Serial number

The router’s serial number. The serial number may be required for
troubleshooting.

Zipcode

ZIP code of the router site.

Software Date

Software build date.

Содержание HX90





























































































































Результаты поиска

Содержание HX90

Отзывы:

Hughes HX90, Руководство по установке, Страница: 82 / 124

Результаты поиска

Содержание HX90

Отзывы: