Hughes HX90 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 124

Hughes HX90 Скачать руководство пользователя страница 30

Chapter 4 • Commissioning the satellite router

30

1039456-0001 Revision A

Note:

If the service provider has provided you with an

sbc.cfg

file, you must

complete the procedures in

Uploading the sbc.cfg file to the satellite router

on

page 32 to upload the file to the router.

If you need troubleshooting information concerning satellite-based commissioning,
see the satellite router’s online Help. Access this information through the System
Control Center

Help

link (

Help > Frequently Asked Questions

).

Obtaining an IP address from the satellite router

1. Make sure the installer laptop is configured to support DHCP.
2. Verify that the installer laptop is connected to the router with an Ethernet cable.
3. Open a command prompt or window on the installer laptop.
4. Type

ipconfig/release

.

5. Press

Enter

.

6. Type

ipconfig/renew

.

7. Press

Enter

.

To view all IP configuration commands, open a command prompt window, type

ipconfig/help,

and press

Enter

.

If the router does not assign IP address 192.168.0.2 to the installer laptop, restart the
installer laptop to obtain the IP address.

Verifying the Ethernet connection

Execute a ping test to verify that the Ethernet connection between the satellite
router and the installer laptop is active:

1. Open a command prompt or window on the installer laptop.
2. Type

ping 192.168.0.1

.

3. Press

Enter

.

If the ping is successful, the ping results show that all sent packets were received.

Figure 9: Successful ping test

«
...
28
29
30
31
32
...
»

Содержание HX90





























































































































Отзывы:

Нет отзывов