manualshive.com logo in svg

Hughes HX90, Руководство по установке, Страница: 103 / 124

Поделиться
Скачать
Hughes HX90 Скачать руководство пользователя страница 103

Chapter 8 • Troubleshooting

 

1039456-0001  Revision A

103

d. Plug the power cord back into the power source.
e.

If the power source is DC, 

plug the input cable back into the power supply. 

Do not power cycle the satellite router by unplugging the power cord from the 
router’s rear panel. Doing so could result in static electricity discharge that could 
shock you and/or damage the router.

4. Test the power outlet to make sure there is not a problem with the power 

source.

5. If the LEDs do not turn on, contact Installer Support.

Checking the Power LED

If the Power LED is off, check the power supply connections. (The router does not 
have an off/on switch.) If the Power LED is on, proceed to 

Checking the LAN LED

 on 

page 103.

Checking the LAN LED

If the front panel LAN LED is off:

1. Disconnect and reconnect the Ethernet cable from the router and from the 

computer. Make sure the cable is securely connected to the router LAN port and 
to the computer’s LAN port.

2. If the LAN LED is still off, power cycle the satellite router:

a. Unplug the power cord from the power source.
b.

If the router is connected to a DC power source,

 unplug the DC input cable 

from the satellite router’s power supply.

c. Wait 10 sec.
d. Plug the power cord back into the power source.
e.

If the power source is DC,

 plug the input cable back into the power supply. 

Do not power cycle the satellite router by unplugging the power cord from the 
router’s rear panel. Doing so could result in static electricity discharge that could 
shock you and/or damage the router.

3. If the LAN LED is still off, check the LAN port LEDs on the back panel.

•

If the orange LED is on and the front panel LAN LED is not, contact Installer 
Support for assistance.

•

If both the orange LED and the front panel LAN LED are off, check all network 
equipment that connects the computer with the router, including the 
computer's Ethernet card, Ethernet cable(s) and any switch or hub. Replace 
one or more of the items to try to isolate the problem.

CAUTION

CAUTION

Содержание HX90





























































































































Отзывы:

Нет отзывов