HP StorageWorks SN6000 Скачать руководство пользователя

Страница: 219 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 219

set setup snmp

Description

Configures SNMP on the switch.

Authority

Admin session

Syntax

set setup snmp

common

trap [trap_number]

Operands

common

Prompts you in a line-by-line fashion to change SNMP configuration parameters that are common

for all traps. For each parameter, enter a new value or press

Enter

to accept the current value. To

configure common parameters and trap parameters, omit the common operand.

Table 50

describes the common SNMP configuration parameters.

Table 50

Common SNMP configuration parameters

Parameter

Description

SNMPEnabled

Enables (

True

) or disables (

False

) SNMP on the switch. The default is

True

Contact

Specifies the name of the person to be contacted to respond to trap

events. The name can be up to 64 characters excluding #, semicolon (;),

and comma (,). The default is undefined. This value is also passed to the

Call Home service configuration.

Location

Specifies the name of the switch location. The name can be up to 64

characters excluding #, semicolon (;), and comma (,). The default is

undefined. This value is also passed to the Call Home service

configuration.

ReadCommunity

Read community password that authorizes an SNMP agent to read

information from the switch. This is a write-only field. The value on the

switch and the SNMP management server must be the same. The read

community password can be up to 32 characters excluding #, semicolon

(;), and comma (,). The default is

public

WriteCommunity

Write community password that authorizes an SNMP agent to write

information to the switch. This is a write-only field. The value on the

switch and the SNMP management server must be the same. The write

community password can be up to 32 characters excluding #, semicolon

(;), and comma (,). The default is

private

TrapCommunity

Trap community password that authorizes an SNMP agent to receive

traps. This is a write-only field. The value on the switch and the SNMP

management server must be the same. The trap community password

can be up to 32 characters excluding #, semicolon (;), and comma (,).

The default is

public

AuthFailureTrap

Enables (

True

) or disables (

False

) the generation of traps in response

to trap authentication failures. The default is

False

ProxyEnabled

Enables (

True

) or disables (

False

) SNMP communication with other

switches in the fabric. The default is

True

SNMPv3Enabled

Enables (

True

) or disables (

False

) SNMP version 3. The default is

False

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды