HP StorageWorks SN6000 Скачать руководство пользователя страница 203

Страница: 203 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 203

set config threshold

Description

Sets the port alarm threshold parameters by which the switch monitors port performance and

generates alarms. The changes you make with this command are not retained when you reset or

power-cycle the switch unless you save them using the

config save

command.

Authority

Admin session and a Config Edit session

Syntax

set config threshold

Initiates a configuration session by which to generate and log alarms for selected events. The system

displays each event, its triggers, and a sampling window one line at a time and prompts you for a

value. For each parameter, enter a new value or press

Enter

to accept the current value shown in

brackets.

Table 37

describes the port alarm threshold parameters.

Table 37

Port alarm threshold parameters

Parameter

Description

ThresholdMonitoringEnabled

Master enable/disable parameter for all events. Enables

(

True

) or disables (

False

) the generation of all

enabled event alarms. The default is

False

CRCErrorsMonitoringEnabled

DecodeErrorsMonitoringEnabled

ISLMonitoringEnabled

LoginMonitoringEnabled

LogoutMonitoringEnabled

LOSMonitoringEnabled

The event type enable/disable parameter. Enables

(

True

) or disables (

False

) the generation of alarms for

each of the following events:

•

CRC errors

•

Decode errors

•

ISL connection count

•

Device login errors

•

Device logout errors

•

Loss-of-signal errors

RisingTrigger

The event count above which a rising trigger alarm is

logged. The switch will not generate another rising

trigger alarm for that event until the count descends

below the falling trigger and again exceeds the rising

trigger.

FallingTrigger

The event count below which a falling trigger alarm is

logged. The switch will not generate another falling

trigger alarm for that event until the count exceeds the

rising trigger and descends again below the falling

trigger.

SampleWindow

The time in seconds in which to count events

Notes

The switch will down a port if an alarm condition is not cleared within three consecutive sampling

windows (by default, 30 seconds). Reset the port to bring it back online. An alarm is cleared when

the threshold monitoring detects that the error rate has fallen below the falling trigger.

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды