HP StorageWorks SN6000 Скачать руководство пользователя страница 205

Страница: 205 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 205

set config zoning

Description

Configures the zoning database. The changes you make with this command are not retained when

you reset or power-cycle the switch unless you save them using the

config save

command.

Authority

Admin session and a Config Edit session

Syntax

set config zoning

Initiates an editing session in which to change the zoning database configuration. The system

displays each parameter one line at a time and prompts you for a value. For each parameter, enter

a new value or press

Enter

to accept the current value shown in brackets.

Table 38

describes the

zoning configuration parameters.

Table 38

Zoning configuration parameters

Parameter

Description

MergeAutoSave

Enables (

True

) or disables (

False

) the saving of changes to active zone

set in the switch’s non-volatile zoning database.The default is

True

Disabling the

MergeAutoSave

parameter can be useful for preventing the

propagation of zoning information when experimenting with different

zoning schemes. However, leaving the

MergeAutoSave

parameter

disabled can disrupt device configurations should a switch have to be reset.

For this reason, the

MergeAutoSave

parameter should be enabled in a

production environment.

DefaultZone

Enables (

Allow

) or disables (

Deny

) communication among ports/devices

that are not defined in the active zone set. The default is

Allow

DiscardInactive

Enables (

True

) or disables (

False

) the discarding of all inactive zone sets

from that zoning database. Inactive zone sets are all zone sets except the

active zone set. The default is

False

Examples

The following is an example of the

set config zoning

command.

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> config edit

The config named default is being edited.

SN6000 FC Switch (admin-config) #> set config zoning

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.

MergeAutoSave (True / False) [True ]

DefaultZone (Allow / Deny) [Allow ]

DiscardInactive (True / False) [False]

Finished configuring attributes.

This configuration must be saved (see config save command) and

activated (see config activate command) before it can take effect.

To discard this configuration use the config cancel command.

See also

config

, page 136

show config zoning

, page 242

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды