HP StorageWorks SN6000 Скачать руководство пользователя страница 61

Страница: 61 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

Modifying port operating characteristics

You can make permanent or temporary changes to port operating characteristics. The

set config port

command makes permanent port configuration changes. These changes are saved in

the active configuration and are preserved across switch or port resets. The

set port

command makes

temporary changes that apply until the next port or switch reset, or until you activate a configuration.

IMPORTANT:

8 Gb/s SFPs do not support the 1 Gb/s setting. Setting a Fibre Channel port that has an

8-Gb/s SFP transceiver to 1-Gb/s will down the port.

The following example permanently changes port administrative state of port 1:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> config edit

SN6000 FC Switch (admin-config) #> set config port 1

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

Configuring Port Number: 1

------------------------

AdminState (1=Online, 2=Offline, 3=Diagnostics, 4=Down) [Online]

offline

LinkSpeed (1=1Gb/s, 2=2Gb/s, 4=4Gb/s, 8=8Gb/s, A=Auto) [Auto ]

PortType (GL, G, F, FL, TR) [GL ]

SymPortName (string, max=32 chars) [Port1 ]

ALFairness (True / False) [False ]

DeviceScanEnable (True / False) [True ]

ForceOfflineRSCN (True / False) [False ]

ARB_FF (True / False) [False ]

InteropCredit (decimal value, 0-255) [0 ]

FANEnable (True / False) [True ]

AutoPerfTuning (True / False) [True ]

MSEnable (True / False) [True ]

NoClose (True / False) [False ]

IOStreamGuard (Enable / Disable / Auto) [Auto ]

PDISCPingEnable (True / False) [True ]

Finished configuring attributes.

This configuration must be saved (see config save command) and

activated (see config activate command) before it can take effect.

To discard this configuration use the config cancel command.

SN6000 FC Switch (admin-config) #> config save

SN6000 FC Switch (admin-config) #> config activate

You can configure all ports based on a specified source port using the

set config ports

command.

The

set config ports

command prompts you to configure the parameters of the source port, and then

applies those values to all of the ports. The following example configures all ports based on port 3:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) config edit

SN6000 FC Switch (admin) #> set config ports 3

SN6000 FC Switch (admin-config)#> config save

SN6000 FC Switch (admin)#> config activate

SN6000 FC Switch (admin)#> admin end

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды