HP StorageWorks SN6000 Скачать руководство пользователя

Страница: 65 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide

To enable port binding for the selected port and to specify the WWNs of the authorized ports/devices,

enter the

set config security portbinding

command. The following example enables port

binding on port 1 and specifies two device world wide names:

SN6000 FC Switch #>

admin start

SN6000 FC Switch (admin) #>

config edit

SN6000 FC Switch (admin-config) #>

set config security port 1

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

PortBindingEnabled (True / False)[False]

true

WWN (N=None / WWN)[None ]

10:00:00:c0:dd:00:b9:f9

WWN (N=None / WWN)[None ]

10:00:00:c0:dd:00:b9:f8

WWN (N=None / WWN)[None ]

Finished configuring attributes.

This configuration must be saved (see config save command) and

activated (see config activate command) before it can take effect.

To discard this configuration use the config cancel command.

Resetting a port

To reinitialize one or more ports and to discard any temporary changes that have been made to the

administrative state or link speed, enter the

reset port

command. The following example reinitializes

port 1:

SN6000 FC Switch #> reset port 1

Configuring port threshold alarms

The switch can monitor a set of port errors and generate alarms based on user-defined sample windows

and thresholds. These port errors include the following:

•

Cyclic redundancy check (CRC) errors

•

Decode errors

•

ISL connection count

•

Device login errors

•

Device logout errors

•

Loss-of-signal errors

You make changes to the port threshold alarms by modifying the switch configuration as described in

”

Modifying a switch configuration

” (page 45). See

Table 37

for a description of the port alarm threshold

parameters.
The switch will down a port if an alarm condition is not cleared within three consecutive sampling windows

(by default, 30 seconds). Reset the port to bring it back online. An alarm is cleared when the threshold

monitoring detects that the error rate has fallen below the falling trigger.

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды