HP StorageWorks SN6000 Скачать руководство пользователя

Страница: 169 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 169

Direction

Direction of the data traffic to which the policy is to be applied:

•

In—Data entering the source

•

Out—Data leaving the source

Priority

A number from –2147483647 to +214783647 that determines

priority for this policy in the security policy database. The higher the

number, the higher the priority.

Action

Processing to apply to data traffic:

•

Discard—Unconditionally disallow all inbound or outbound

data traffic.

•

None—Allow all inbound or outbound data traffic without

encryption or decryption.

•

Ipsec—Apply IP security to inbound and outbound data traffic.

ProtectionDesired

Type of IP security protection to apply:

•

AH—Authentication Header

•

ESP—Encapsulating Security Payload

•

Both—Apply both AH and ESP protection

ahRuleLevel

Rule level to apply for AH protection:

•

Default—Use the system wide default for the protocol

•

Use—Use a security association if one is available

•

Require—A security association is required whenever a packet is

sent that is matched with the policy

espRuleLevel

Rule level to apply for ESP protection:

•

Default—Use the system wide default for the protocol

•

Use—Use a security association if one is available

•

Require—A security association is required whenever a packet is

sent that is matched with the policy

Table 14

Policy configuration parameters (continued)

Parameter

Description

Operands

delete [policy]

Deletes the policy given by [policy] from the Security Policy database. You must enter the

ipsec save

command afterwards to save your changes.

edit [policy]

Opens an edit session in which to change the configuration of an existing policy given by

[policy].

list

[option]

Displays the configuration for the policies given by [option]. If you omit [option], the command

displays the configuration of all active policies. [option] can be one of the following:

[policy]

Displays the configuration for the policy given by [policy].

active

Displays the configuration for all active policies.

configured

Displays the configuration for all user-defined policies.

edited

Displays the configuration for all policies that have been modified, but not saved.

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды