HP StorageWorks SN6000 Скачать руководство пользователя страница 157

Страница: 157 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 157

hotreset

Description

Resets the switch for the purpose of activating the pending firmware without disrupting traffic. This

command terminates all management sessions, saves all configuration information, and clears the

event log. After the pending firmware is activated, the configuration is recovered. This process may

take a few minutes. To save the event log to a file before resetting, enter the

set log archive

command.

Authority

Admin session

Syntax

hotreset

Notes

You can load and activate firmware upgrades on an operating switch without disrupting data traffic

or having to re-initialize attached devices. If the non-disruptive activation fails, you will usually be

prompted to try again later. Otherwise, the switch will perform a disruptive activation. Verify that the

current firmware version supports the installation and non-disruptive activation of the new firmware

version. For information about compatible firmware versions, see the

Firmware Release Notes

To ensure a successful non-disruptive activation, you should first satisfy the following conditions:

•

No changes are being made to switches in the fabric including installing firmware, powering up,

powering down, disconnecting or connecting ISLs, and changing the switch configuration.

•

No port on the switch is in the diagnostic state.

•

No zoning changes are being made on the switch.

•

No changes are being made to attached devices, including powering up, powering down,

disconnecting, connecting, and HBA configuration changes.

•

No more than two Simple SAN Connection Manager sessions are open.

Ports that change states during the non-disruptive activation are reset. When the non-disruptive

activation is complete, Simple SAN Connection Manager sessions, QuickTools sessions, and

Enterprise Fabric Management Suite sessions are automatically reconnected. However, Telnet

sessions must be restarted manually.
This command clears the event log and all counters.

TIP:

After upgrading firmware that includes changes to QuickTools, a QuickTools session that was

open during the upgrade may indicate that the new firmware is not supported. To correct this, close

the QuickTools session and the browser window, then open a new QuickTools session.

See also

hardreset

, page 154

reset

, page 180

set log

, page 206

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды