HP StorageWorks SN6000 Скачать руководство пользователя страница 274

Страница: 274 / 330

274 Command Reference

show switch

Description

Displays switch operational information.

Authority

None

Syntax

show switch

Notes

Table 65

describes the switch operational parameters.

Table 65

Switch operational parameters

Parameter

Description

SymbolicName

Descriptive name for the switch

SwitchWWN

Switch worldwide name

BootVersion

Programmable Read-only Memory (PROM) boot version

CreditPool

Number of port buffer credits available to recipient ports

DomainID

Switch domain ID

FirstPortAddress

Fibre Channel address of switch port 0

FlashSize - MBytes

Size of the flash memory, in megabytes

LogFilterLevel

Event severity level, used to record events in the event log

MaxPorts

Number of ports available on the switch

NumberOfResets

Number of times the switch has been reset over its service

life

ReasonForLastReset

Action that caused the last reset

ActiveImageVersion-build

date

Active firmware image version and build date

PendingImageVersion-build

date

Firmware image version and build date that is pending.

This image will become active at the next reset or

power-cycle.

ActiveConfiguration

Name of the switch configuration that is in use.

AdminState

Switch administrative state

AdminModeActive

Admin session status

BeaconOnStatus

Beacon status as set by the

set beacon

command

OperationalState

Switch operational state

PrincipalSwitchRole

Principal switch status. True indicates that this switch is the

principal switch.

POSTFaultCode

Fault code from the most recent power-on self test

POSTStatus

Status from the most recent power-on self test

TestFaultCode

Fault code from the most recent switch test

TestStatus

Status from the most recent switch test

BoardTemp (1) - Degrees

Celsius

Internal switch temperature at circuit board sensor 1

SwitchTemperatureStatus

Normal, warning, failure

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды