HP StorageWorks SN6000 Скачать руководство пользователя страница 195

Страница: 195 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 195

set config port

Description

Sets the port configuration parameters for one or more ports. The changes you make with this

command are not retained when you reset or power-cycle the switch unless you save them using the

config save

command.

Authority

Admin session and a Config Edit session

Syntax

set config port

[port_number]

set config ports

[port_number]

Operands

port

[port_number]

Initiates an edit session in which to change configuration parameters for the port number given

by [port_number]. If you omit [port_number], the system begins with port 0 and proceeds in

order through the last port. For each parameter, enter a new value or press

Enter

to accept the

current value shown in brackets. Enter

to end the configuration for one port, or

to end the

configuration for all ports.

Table 33

describes the port configuration parameters.

ports

[port_number]

Initiates an editing session in which to change configuration parameters for all ports based on

the configuration for the port given by [port_number]. If you omit [port_number], port 0 is used.

For each parameter, enter a new value or press

Enter

to accept the current value shown in

brackets. Enter

to end the configuration.

Table 33

describes the port configuration parameters.

Table 33

Port configuration parameters

Parameter

Description

AdminState

Port administrative state:

•

Online—Activates and prepares the port to send data. This is the

default.

•

Offline—Prevents the port from receiving signal and accepting a

device login.

•

Diagnostics—Prepares the port for testing and prevents the port from

accepting a device login.

•

Down—Disables the port by removing power from the port lasers.

LinkSpeed

Transmission speed:

•

SFP ports: 2 Gb/s, 4 Gb/s, 8 Gb/s, or Auto. The default is Auto. 8

Gb/s SFPs do not support the 1 Gb/s setting. Settting a port to 1

Gb/s that has an 8 Gb/s SFP downs the port.

•

XPAK ports: 10 Gb/s, 20 Gb/s, Auto

PortType

Port types:

•

SFP ports: GL, G, F, FL, Donor. The default is GL.

•

XPAK ports: G, F. The default is G.

SymbolicPortName

Descriptive name for the port. The name can be up to 32 characters

excluding #, semicolon (;), and comma (,). The default is

Port

, where

is the port number.

ALFairness

Arbitration loop fairness. Enables (

True

) or disables (

False

) the

switch’s priority to arbitrate on the loop. The default is

False

DeviceScanEnabled

Enables (

True

) or disables (

False

) the scanning of the connected

device for FC-4 descriptor information during login. The default is

True

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды