CommScope LightCrimp Plus ST Скачать руководство пользователя страница 1

Страница: 1 / 16

Instruction Sheet

LightCrimp Plus® ST

408--4457

of 16

FEB 2017 Rev

Fiber Optic Connector Kits

Figure 1

Connector

Assembly

Bare Buffer

Boot

Plunger

Protective Cap

Strain

Relief

Crimp

Eyelet

Inner

Eyelet

Small

Tubing

Black

Tubing

Clear

Tubing

Connector kit is shipped with these installed onto connector

assembly. Keep them in place until ready for assembly.

Ferrule Protective

Cover

Verify that Instruction Sheet

(408- Series)

Pertains to Connector Kit

Being Terminated

To Verify, Refer to Product Drawing for

Applicable Instruction Sheet at:

(Search by Connector Kit Part Number,

Click on the Part Number

Click on Product Drawing)

1. INTRODUCTION

LightCrimp Plus ST fiber optic connector kits are

designed for use with 125--

m singlemode or

multimode glass fiber optic cable. These kits can be

used with any of the following media (paragraph of

assembly procedure is indicated next to media).

5.1. 900-

m Bare Buffered Fiber

5.2. 250-

m Coated Fiber

5.3. 2.0- to 3.0- mm Loose Jacketed Cable

5.4. 900-

m Easy Strip or Semi- Tight Buffered Fiber

Read these instructions thoroughly before assembling

the connector kits.

All numerical values in this instruction sheet

are in metric units. Dimensions are in

millimeters Figures are not drawn to scale.

Reasons for reissue of this instruction sheet are

provided in Section 6, REVISION SUMMARY.

2. DESCRIPTION

(See Figure 1)

Each connector kit consists of a connector assembly,

strain relief, inner eyelet, crimp eyelet, black tubing,

and clear tubing. Each kit is also supplied with a bare

buffer boot and small tubing to compensate for small

diameter cable. Also included, assembled onto the

connector, is a ferrule protective cover for the ferrule

(front of connector) and a plunger protective cap for

the plunger (rear of connector).

3. SAFETY PRECAUTIONS

NEVER look into the end of terminated or

unterminated fibers. Laser radiation is invisible

but can damage eye tissue. NEVER eat, drink, or

smoke when working with fibers. This could lead

to ingestion of glass particles.

Be very careful to dispose offi ber ends properly.

The fibers create slivers that can easily puncture

the skin and cause irritation.

DO NOT use defective or damaged components.

Replace them with new components.

NOTE

DANGER

CAUTION

www.commscope.com

To obtain information on

CommScope

® products, visit our website at

www.commscope.com/SupportCenter

This product is covered by one or more U.S.

patents or their foreign equivalents. For patents, see

www.commscope.com/ProductPatent/ProductPatent.aspx

Содержание LightCrimp Plus ST

















Результаты поиска

Содержание LightCrimp Plus ST

Отзывы:

Похожие инструкции для LightCrimp Plus ST

Бренды по названию

Популярные бренды

CommScope LightCrimp Plus ST, Инструкция

Результаты поиска

Содержание LightCrimp Plus ST

Отзывы:

Похожие инструкции для LightCrimp Plus ST

Бренды по названию

Популярные бренды