HP StorageWorks SN6000 Скачать руководство пользователя страница 197

Страница: 197 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 197

IOStreamGuard

Enables or disables the suppression of RSCN messages.

IOStreamGuard

can have the following values:

•

Enable

—Suppresses the reception of RSCN messages from other

ports for which IOStreamGuard is enabled.

•

Disable

—Allows free transmission and reception of RSCN

messages.

•

Auto

—Suppresses the reception of RSCN messages when the port is

connected to an initiator device with a QLogic HBA. For older QLogic

HBAs, such as the QLA2200, the

DeviceScanEnabled

parameter

must also be enabled. The default is

Auto

PDISCPingEnable

(SFP ports only)

Enables (

True

) or disables (

False

) the transmission of ping messages

from the switch to all devices on a loop port. The default is

True

Table 33

Port configuration parameters (continued)

Parameter

Description

Examples

The following is an example of the

set config port

command:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> config edit

SN6000 FC Switch (admin-config) #> set config port 1

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

Configuring Port Number: 1

------------------------

AdminState (1=Online, 2=Offline, 3=Diagnostics, 4=Down) [Online]

LinkSpeed (1=1Gb/s, 2=2Gb/s, 4=4Gb/s, 8=8Gb/s, A=Auto) [Auto ]

PortType (GL, G, F, FL, TR ) [GL ]

SymPortName (string, max=32 chars) [Port1 ]

ALFairness (True / False) [False ]

DeviceScanEnable (True / False) [True ]

ForceOfflineRSCN (True / False) [False ]

ARB_FF (True / False) [False ]

InteropCredit (decimal value, 0-255) [0 ]

FANEnable (True / False) [True ]

AutoPerfTuning (True / False) [True ]

MSEnable (True / False) [True ]

NoClose (True / False) [False ]

IOStreamGuard (Enable / Disable / Auto) [Auto ]

PDISCPingEnable (True / False) [True ]

Finished configuring attributes.

This configuration must be saved (see config save command) and

activated (see config activate command) before it can take effect.

To discard this configuration use the config cancel command.

Содержание StorageWorks SN6000











































































































































































































































































































































Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды

HP StorageWorks SN6000, Руководство по интерфейсу командной строки

Результаты поиска

Содержание StorageWorks SN6000

Отзывы:

Похожие инструкции для StorageWorks SN6000

Бренды по названию

Популярные бренды