manualshive.com logo in svg

Honeywell CM4, Техническое руководство

TDK-Lambda CM4 - надежный и эффективный источник питания для широкого спектра применений. Загружайте бесплатные руководства по использованию и приложения на manualshive.com, чтобы максимально эффективно использовать эту продукцию.

Поделиться
Скачать
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

v

Table of Contents

3.4 Sample Locations  ...................................................................................... 3-4

3.4.1 Sample Line Particulate Filter Use ............................................. 3-4
3.4.2 Special Considerations for Positive   

         Pressure . 3-4

3.5 Configuring for Mounting Method ...................................................... 3-4

3.5.1 Wall Mount ........................................................................................ 3-5
3.5.2 Rack Mount Kit ................................................................................. 3-6
3.5.3 Rack Mounting the CM4-P ........................................................... 3-7
3.5.4 Rack Enclosures ............................................................................... 3-7

3.6 Installing Sample Lines ............................................................................. 3-9

3.6.1 Sample Line Requirements for Installation............................ 3-9
3.6.2 Tubing Connections .....................................................................3-10
3.6.3 Sample Line Inlet Connections ................................................3-10
3.6.4 Point Legend ...................................................................................3-10

3.7 Installing Sample Line Particulate Filters .........................................3-11
3.8 Installing Pump Exhaust Line ...............................................................3-11

3.8.1 Exhaust Line Installation Guidelines ......................................3-11
3.8.2 Exhaust Tubing Specifications  .................................................3-11

3.9 Connecting AC Power Cord ..................................................................3-11
3.10 Wiring Relays ...........................................................................................3-12

3.10.1 Relay Contacts .............................................................................3-12
3.10.2 Ratings  ...........................................................................................3-12
3.10.3 Wiring Guidelines .......................................................................3-13

3.11 Wiring Optional Current Loop (4-20 mA Output) ......................................... 3-13
3.12 Loading Chemcassette

®

 Tape .............................................................3-14

3.13 Power On/Off ...........................................................................................3-14
3.14 Installation Notice ..................................................................................3-14
3.15 Function and Cursor Keys ...................................................................3-15

3.15.1 MONITOR .......................................................................................3-15

3.15.2 PROGRAM ......................................................................................3-15
3.15.3 RESET/ESCAPE .............................................................................3-15
3.15.4 ENTER ..............................................................................................3-15
3.15.5 CURSOR ARROW LEFT/RIGHT .................................................3-15

4 Basic Operation

4.1 Introduction ................................................................................................. 4-2
4.2 Monitor Mode .............................................................................................. 4-2

4.2.1 Exiting Monitor Mode ................................................................... 4-3
4.2.2 Printing Time Weighted Averages (TWA) During Monitor 

Mode .............................................................................................................. 4-3
4.2.3 Point Lock-On During Monitor Mode ...................................... 4-3
4.2.4 Display Lock-On During Monitor Mode  ................................. 4-4
4.2.5 Alarm History During Monitor.................................................... 4-4
4.2.6 Fault History During Monitor Mode ......................................... 4-5
4.2.7 Display Point Flows During Monitor Mode ............................ 4-5
4.2.8 Advance Chemcassette Tape During Monitor Mode..........................4-5

4.3 Program Mode ............................................................................................. 4-5
4.4 Alarms and Faults ....................................................................................... 4-6

4.4.1 Alarms ................................................................................................. 4-6
4.4.2 Faults ................................................................................................... 4-6

4.5 Accessing Programming Functions ..................................................... 4-6

4.5.1 Programming by Scrolling ........................................................... 4-7
4.5.2 Programming Using Direct Numeric Entry ............................ 4-7

4.6 CM4 Menu Structure ................................................................................. 4-8
4.7 Keypad Locking Feature .......................................................................... 4-9

5 Calibration Mode Functions

5.1 Introduction ................................................................................................. 5-2
5.2 Function 1.1 – Optics Verify .................................................................... 5-2

珠海司福斯特科技有限公司

www.safedtech.com

Содержание CM4











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CM4

Bacharach 300 Instructions Manual preview
300
Бренд: Bacharach Страницы: 87
Bacharach PCA 2 Instruction, Operating & Maintenance preview
PCA 2
Бренд: Bacharach Страницы: 60
Bacharach HGM-MZ Product Bulletin preview
HGM-MZ
Бренд: Bacharach Страницы: 4
Bacharach HGM-MZ Maintenance And Troubleshooting Manual preview
HGM-MZ
Бренд: Bacharach Страницы: 17
Eagle Eye Power Solutions Vigilant ELM Series Troubleshooting Manual preview
Vigilant ELM Series
Бренд: Eagle Eye Power Solutions Страницы: 9
FCI ST100 series Operation Manual preview
ST100 series
Бренд: FCI Страницы: 44
FCI ST100 series Manual preview
ST100 series
Бренд: FCI Страницы: 36
FCI ST100 series Configuration Software Manual preview
ST100 series
Бренд: FCI Страницы: 26
National Instruments NI 9219 Getting Started Manual preview
NI 9219
Бренд: National Instruments Страницы: 38
Omega DP3001 User Manual preview
DP3001
Бренд: Omega Страницы: 24
Bahco BMMTRS1 Original Instructions Manual preview
BMMTRS1
Бренд: Bahco Страницы: 21
Kübler Ants LEB02 Operation Manual preview
Ants LEB02
Бренд: Kübler Страницы: 72
Xylem Ai1 Series Quick Start Manual preview
Ai1 Series
Бренд: Xylem Страницы: 39
Ahlborn ALMEMO 2790 Operating Instructions Manual preview
ALMEMO 2790
Бренд: Ahlborn Страницы: 32
Texmate DL-40JANUS-DCA Manual preview
DL-40JANUS-DCA
Бренд: Texmate Страницы: 15
Cable Detection Utili-Gen User Manual preview
Utili-Gen
Бренд: Cable Detection Страницы: 2
Swan Analytical Instruments AMI INSPECTOR Hydrogen Operator'S Manual preview
AMI INSPECTOR Hydrogen
Бренд: Swan Analytical Instruments Страницы: 74
Rohde & Schwarz RT-ZS10 User Manual preview
RT-ZS10
Бренд: Rohde & Schwarz Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды