manualshive.com logo in svg

Honeywell CM4, Техническое руководство

TDK-Lambda CM4 - надежный и эффективный источник питания для широкого спектра применений. Загружайте бесплатные руководства по использованию и приложения на manualshive.com, чтобы максимально эффективно использовать эту продукцию.

Поделиться
Скачать
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

7-11

recent concentration reading. However, it will not report any changes in 

the concentration during this period, because the tape is saturated.
The Monitor relay (RY6) will energize when monitoring is temporarily 

suspended  due  to  tape  saturation.  Note  however,  any  one  point 

that  is  enabled  for  Duty  Cycle  will  cause  the  Monitor  relay  (RY6)  to 

energize regardless if some points have not been selected (enabled) 

for Duty Cycle. In the CM4 software, the “monitor relay action during 

Duty  Cycle”  bits  default  to TRUE,  but  can  be  set  to  FALSE  with  the 

following procedure.
Instruction
If the Duty Cycle option is installed, you can use Menu Function 3.3.6 

(EN/DIS Duty Cycle) to enable or disable the Duty Cycle function for 

each point. Use Menu Function 3.5.6 (Set Duty Cycle) to program the 

Duty Cycle time function.
Follow these steps to enable/disable the Duty Cycle for each point:

1.  Press PROGRAM to exit Monitor Mode.
2.  From the 3–SET-UP MENU, choose the subfunction 3–OUTPUT 

OPTIONS, then 6–EN/DIS DUTY CYCLE.

3 – SET-UP MODE

3 – OUTPUT OPTION

6 – EN/DIS DUTY CYCLES

NOTE:

Duty Cycle is a factory-enabled option. If not set at the factory, 

then it is not available to user.

3.  The display reads:

SELECT POINT

Use the numeric keys to specify a point.

4.  The display will read:

PT 1 ENABLE 1=Y 0=N

Choose 1 or 0 to enable or disable that point for Duty Cycle.

5.  S e l e c t   o t h e r   p o i n t s ,   i f   d e s i r e d ,   o r   p r e s s  

RESET/ESCAPE key.

7.5 Function 3.4 – Configuration

Purpose
Use the configuration function to:

•  Save new instrument configurations
•  Restore  an  existing  instrument  configuration  after  changing 

configuration  parameters  or  a  RESET  SYSTEM  that  returned 

parameters to the factory default

System configuration consists of all configurable parameters defined 

in the Set-Up Menu.

Instructions

1.  Press PROGRAM to exit Monitor Mode.
2.  From  the  3–SET-UP  MENU,  choose  the  subfunction 

4–CONFIGURATION. 

3 – SET-UP MODE

4 – CONFIGURATION

 

The display reads:

1=SAVE 2=LOAD CONFIG

珠海司福斯特科技有限公司

www.safedtech.com

Содержание CM4











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CM4

TANDBERG 15 Series General And Technical Information preview
15 Series
Бренд: TANDBERG Страницы: 53
B meters IWM-TX5 Quick Start Manual preview
IWM-TX5
Бренд: B meters Страницы: 2
Camille Bauer SIRAX BM1450 Safety Instructions preview
SIRAX BM1450
Бренд: Camille Bauer Страницы: 11
Camille Bauer SINEAX AM1000 Device Handbook preview
SINEAX AM1000
Бренд: Camille Bauer Страницы: 83
E-Mon Din-Mon D5 Installation Instructions Manual preview
Din-Mon D5
Бренд: E-Mon Страницы: 72
YATO YT-72977 Manual preview
YT-72977
Бренд: YATO Страницы: 36
Dynojet Dynoware RT Installation Manual preview
Dynoware RT
Бренд: Dynojet Страницы: 88
VP instruments VPLog-i-R User Manual preview
VPLog-i-R
Бренд: VP instruments Страницы: 15
LaserLiner F090.122A Manual preview
F090.122A
Бренд: LaserLiner Страницы: 80
Badger Meter Trimble Ranger 3 Installation Manual preview
Trimble Ranger 3
Бренд: Badger Meter Страницы: 20
A&D FX-i Series Quick Start Manual preview
FX-i Series
Бренд: A&D Страницы: 38
OTOVATION Amplitude T Series Installation Manual preview
Amplitude T Series
Бренд: OTOVATION Страницы: 15
Fungilab V-Pad Instruction Manual preview
V-Pad
Бренд: Fungilab Страницы: 47
Kawai CN24 Owner'S Manual preview
CN24
Бренд: Kawai Страницы: 56
Keysight M9703A Series Startup Manual preview
M9703A Series
Бренд: Keysight Страницы: 26
janitza UMG 605 Operating Manual preview
UMG 605
Бренд: janitza Страницы: 92
PASCO PS-3217 Instruction Manual preview
PS-3217
Бренд: PASCO Страницы: 4
National Instruments PXIe-5632 Getting Started Manual preview
PXIe-5632
Бренд: National Instruments Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды