manualshive.com logo in svg

Honeywell CM4, Техническое руководство

TDK-Lambda CM4 - надежный и эффективный источник питания для широкого спектра применений. Загружайте бесплатные руководства по использованию и приложения на manualshive.com, чтобы максимально эффективно использовать эту продукцию.

Поделиться
Скачать
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

2-3

2.2.2 LEDs and Point ID Labels

Each of the four detection points includes two LEDs:

•  Point status LED
•  Point alarm LED

Point Status LED
The monitoring status LEDs indicate the following conditions:

•  Green for the specific point when the CM4 is monitoring that 

point

•  Yellow, steady or flashing indicating fault
•  Red, steady or flashing indicating alarm
•  Off when the CM4 is not monitoring that point

Alarm LED
To indicate gas alarm condition, the LEDs:

•  Light  steady  red  when  Level  1  alarm  (low  level  gas  alarm) 

occurs for any monitored point

•  Flash  red  when  Level  2  alarm  (high  level  gas  alarm)  occurs 

for any monitored point

Point ID Labels
Identify each point using the write-on surface provided. Use a fiber-

tipped  permanent  marker. You  can  remove  any  marks  with  acetone 

without damaging the panel.

2.2.3 Keypad

The keypad consists of:

•  Numeric keys
•  Function keys
•  Cursor Arrow Left/Right keys

Numeric Keys
Use the numeric keys, 1 through 9 and 0, to:

•  Enter programming values
•  Display and select specific detection points

Function Keys
Function keys access menus and functions. Function keys include:

•  MONITOR
•  PROGRAM
•  RESET
•  ENTER

Functions  are  described  in  detail  later  in  this  manual,  Sections  4 

through 8.
Cursor Arrow Right/Left Keys
Cursor Arrow Left/Right keys scroll the display backwards and forwards 

to program and view information. Pressing the cursor arrow keys twice 

while monitoring also advances the tape.

2.2.4 Power Indicator LED

The power indicator LED is:

•  On steady green during operation
•  Flashes yellow to indicate the keypad is locked

See 

Section  7.1.1

  to  activate  the  keypad  using  the  passcode.  See 

Section 7.7

 for passcode information.

珠海司福斯特科技有限公司

www.safedtech.com

Содержание CM4











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CM4

Magnetic Instrumentation 2130 Instruction Manual preview
2130
Бренд: Magnetic Instrumentation Страницы: 63
Bamo Pooltest 3 Instruction Manual preview
Pooltest 3
Бренд: Bamo Страницы: 8
Han Seung HTS-CT10 Operating Manual preview
HTS-CT10
Бренд: Han Seung Страницы: 2
semaphore KINGFISHER PLUS+ Hardware Reference Manual preview
KINGFISHER PLUS+
Бренд: semaphore Страницы: 247
Jaquet T411 Operating Instructions Manual preview
T411
Бренд: Jaquet Страницы: 27
PASCO SF-9500A Instruction Sheet preview
SF-9500A
Бренд: PASCO Страницы: 2
Observator Instruments Analite NEP-5000 Manual preview
Analite NEP-5000
Бренд: Observator Instruments Страницы: 103
pts Diagnostics A1CNow Quick Reference Manual preview
A1CNow
Бренд: pts Diagnostics Страницы: 2
Spectroline LeakTracker OIL-GLO ULTRA Instruction Manual preview
LeakTracker OIL-GLO ULTRA
Бренд: Spectroline Страницы: 12
Feasa ICT Series User Manual preview
ICT Series
Бренд: Feasa Страницы: 145
VECTECH 492EP Operation Manual preview
492EP
Бренд: VECTECH Страницы: 10
Ocean Optics CHEM2000-UV-VIS Operating Manual And User Manual preview
CHEM2000-UV-VIS
Бренд: Ocean Optics Страницы: 42
Labom GA261 Series Operating Instructions Manual preview
GA261 Series
Бренд: Labom Страницы: 6
Dairymaster MOOMONITOR + User Manual preview
MOOMONITOR +
Бренд: Dairymaster Страницы: 14
STEINEL 4007841014919 Manual preview
4007841014919
Бренд: STEINEL Страницы: 188
Accumet AP71 Operating Instructions Manual preview
AP71
Бренд: Accumet Страницы: 24
Befaco BF22 User Manual preview
BF22
Бренд: Befaco Страницы: 3
Midtronics EBT-965P User Manual preview
EBT-965P
Бренд: Midtronics Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды