manualshive.com logo in svg

Honeywell CM4, Техническое руководство

TDK-Lambda CM4 - надежный и эффективный источник питания для широкого спектра применений. Загружайте бесплатные руководства по использованию и приложения на manualshive.com, чтобы максимально эффективно использовать эту продукцию.

Поделиться
Скачать
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

4-5

4.2.6 Fault History During Monitor Mode

Use the fault history function to print and display the four most recent 

faults and alarms. See Figure 4-2.
To print and display the fault history, press ENTER followed by 0.
The fault history is printed (if printer is installed) and displayed showing 

the  most  recent  fault  first. The  display  will  scroll  through  each  fault. 

Use the cursor keys to advance through each fault. 
The printout of the fault history shows the most recent fault first for up 

to eight total faults. The printout includes:

•  Instrument serial number
•  Current date and time
•  Customer name and location
•  Fault number (Fxx)
•  Fault type
•  Fault date and time

The CM4 sends the fault history to the printer.

02/29/05    14:23   CM4-851-0006   FAULT HISTORY 

ABC MANUFACTURING CO., Kansas City, MO

02/29/05 

14:22  F37 

TRANSPORT ERROR

02/29/05 

14:22  F27 

FLOW FAILURE PT1

02/29/05 

14:19  F39 

LOSS OF FLOW PT4

END OF FAULT HISTORY

Figure 4-2: Typical Fault History Printout

The  display  returns  to  normal  20  seconds  after  the  last  keypad 

entry. 
Pressing RESET does not clear fault history.

4.2.7 Display Point Flows During Monitor Mode

Use  the  display  point  flows  to  check  sample  flows  without  leaving 

monitor mode. To set or check the sample flows, press ENTER followed 

by 5. The four flows will be displayed in real time along with the up or 

down arrows if they are out of tolerance:

173

189

165 

182

The  display  will  update  once  per  second. The  display  will  revert  to 

normal operation after 20 seconds or after RESET is pressed.

4.2.8 Advance Chemcassette Tape During Monitor Mode

Press  the  CURSOR  RIGHT  ARROW  twice  to  advance  the  tape  and 

view the stain pattern while remaining in Monitor Mode. Display lock-on 

and point lock-on remain active during this procedure. TWA information 

is uninterrupted.

4.3 Program Mode

To access Program Mode:

1.  Press  PROGRAM  from  Monitor  Mode. The  CM4  displays  the 

message:

END MONITOR? 1=Y   0=N

2.  Press 1 to end Monitor Mode and go to Program Mode.

If you do not press 1 within three seconds, the CM4 returns to Monitor 

Mode.
The CM4 goes to Program Mode and displays:

SELECT PROGRAM  

 

Press CURSOR ARROW LEFT/RIGHT to select items from the four 

program menus.

珠海司福斯特科技有限公司

www.safedtech.com

Содержание CM4











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CM4

OHAUS MC2000 Instruction Manual preview
MC2000
Бренд: OHAUS Страницы: 84
Laserworld GREEN-3000 Manual preview
GREEN-3000
Бренд: Laserworld Страницы: 4
Laserworld GREEN-12000 Manual preview
GREEN-12000
Бренд: Laserworld Страницы: 4
Laserworld GREEN-150E Manual preview
GREEN-150E
Бренд: Laserworld Страницы: 4
LaserLiner SensoLite 120 Quick Start Manual preview
SensoLite 120
Бренд: LaserLiner Страницы: 56
Lasermet ICS-6 Wiring Manual preview
ICS-6
Бренд: Lasermet Страницы: 8
ASCEL Electronic AE20401 Assembly And Operation Manual preview
AE20401
Бренд: ASCEL Electronic Страницы: 64
H.E. Anderson Ratio:Guard Advanced Manual preview
Ratio:Guard Advanced
Бренд: H.E. Anderson Страницы: 9
Oakton WD-35606-00, WD-35606-05 Operating Instructions Manual preview
WD-35606-00, WD-35606-05
Бренд: Oakton Страницы: 10
Fuji Electric ZRE-2 Instruction Manual preview
ZRE-2
Бренд: Fuji Electric Страницы: 85
Maico HY 5 Mounting Instructions And Directions For Use preview
HY 5
Бренд: Maico Страницы: 2
Baker Hughes Panametrics Aurora H2O User Manual preview
Panametrics Aurora H2O
Бренд: Baker Hughes Страницы: 92
phase II UTG-2650 Manual preview
UTG-2650
Бренд: phase II Страницы: 11
Endress+Hauser Cerabar S PMC71 Functional Safety Manual preview
Cerabar S PMC71
Бренд: Endress+Hauser Страницы: 48
Agilent Technologies LogicWave Installation Manual preview
LogicWave
Бренд: Agilent Technologies Страницы: 26
NCL DUAL-BLEND 4114 Installation And Setup Manual preview
DUAL-BLEND 4114
Бренд: NCL Страницы: 7
Bamo BAMOWIZ OX 452 User Manual preview
BAMOWIZ OX 452
Бренд: Bamo Страницы: 16
EUTECH INSTRUMENTS WATERPROOF PHTESTR 1 PH TESTER Instruction Sheet preview
WATERPROOF PHTESTR 1 PH TESTER
Бренд: EUTECH INSTRUMENTS Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды