manualshive.com logo in svg

Honeywell CM4, Техническое руководство

TDK-Lambda CM4 - надежный и эффективный источник питания для широкого спектра применений. Загружайте бесплатные руководства по использованию и приложения на manualshive.com, чтобы максимально эффективно использовать эту продукцию.

Поделиться
Скачать
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

9-4

7.  On older model CM4’s, release carrier retaining tab by pressing 

towards rear of unit.

8.  Remove the carrier by placing your hands under it, palms 

up, and firmly lifting straight up. Apply sufficient upward force 

to free tape guides from posts. See 

Figure 9-1

.

NOTE:

To avoid carrier torque and damage, do not tilt the carrier. Contact 

Honeywell Analytics if you are unable to remove the carrier.

Right

Wrong

Figure 9-1: Removing the Carrier

9.2.2 Verify Optics

Each  time  you  replace  a  Chemcassette

®

  tape,  verify  that  the  CM4 

optics system is operating properly using the optics verify function and 

the  optics  verification  card  supplied  with  your  instrument. The  CM4 

compares the nominal span values stored in the instrument’s memory 

to the values produced by the optics verification card. This procedure 

verifies  that  the  optics  system  correctly  quantifies  gas  levels  during 

normal operation.
Instructions

1.  Press PROGRAM to exit Monitor Mode.
2.  From  the  1–CALIBRATION  MODE,  choose  the  subfunction 

1–OPTICS VERIFY.

1 – CALIBRATION MODE

1 – OPTICS VERIFY

3.  Press ENTER. 

 

The display reads:

INSERT STAIN 1 PRESS    

4.  Open  the  tape  load  lever  and  carefully  remove  carrier  (See 

Figure 9-1).

5.  Insert  the  verification  card  into  the  detector  head  with  Stain 

1  facing  the  front  of  the  CM4.  Make  sure  that  Stain  1  is  fully 

inserted into the detector head. 

6.  Carefully close the tape load lever.
7.  Press  CURSOR  ARROW  RIGHT  on  the  numeric  keypad. The 

readings for Stain 1 are stored. The display reads:

INSERT STAIN 2 PRESS  

8.  Open the tape load lever.
9.  Remove the verification card. 
10.  Turn the card and fully insert Stain 2. 
11.  Carefully close the tape load lever.
12.  Press CURSOR ARROW RIGHT.

The display shows one of two messages:

VERIFY SUCCESSFUL

or

F24 OPTICS FAIL 1, 2, 3, 4

13.  Open the tape load lever and remove the verification card. 

NOTE:

If the optics verification is not successful, repeat the procedure. 

Contact Honeywell Analytics if the instrument prints and displays 

the error message after a second optics verification attempt.

14.  Reinstall the carrier and close the tape load lever.

Press any key to return to the Calibration main menu.

珠海司福斯特科技有限公司

www.safedtech.com

Содержание CM4











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CM4

Vanguard Instruments II Series Operating Instructions Manual preview
II Series
Бренд: Vanguard Instruments Страницы: 24
UE Systems Ultraprobe 9000 Manual preview
Ultraprobe 9000
Бренд: UE Systems Страницы: 25
UE Systems ULTRAPROBE 10000 General Setup And Knowledge preview
ULTRAPROBE 10000
Бренд: UE Systems Страницы: 6
Yamaha Electone B-20CR Manual preview
Electone B-20CR
Бренд: Yamaha Страницы: 16
Endress+Hauser CNGmass DCI Operating Instructions Manual preview
CNGmass DCI
Бренд: Endress+Hauser Страницы: 88
Omega HHF144 User Manual preview
HHF144
Бренд: Omega Страницы: 26
OHAUS STARTER 2100 Service Manual preview
STARTER 2100
Бренд: OHAUS Страницы: 28
Velp Scientifica TB1 Instruction Manual preview
TB1
Бренд: Velp Scientifica Страницы: 32
janitza MRG 512 PQ Flex Operation Manual preview
MRG 512 PQ Flex
Бренд: janitza Страницы: 9
Kurzweil m230 User Manual preview
m230
Бренд: Kurzweil Страницы: 35
PHYWE Cobra SMARTsense Chloride Ion Operating Instructions preview
Cobra SMARTsense Chloride Ion
Бренд: PHYWE Страницы: 4
Keysight M9703A Series Startup Manual preview
M9703A Series
Бренд: Keysight Страницы: 26
DAKOTA ULTRASONICS PZX-7 Operation Manual preview
PZX-7
Бренд: DAKOTA ULTRASONICS Страницы: 51
SCINTREX ENVI-MAG Manual preview
ENVI-MAG
Бренд: SCINTREX Страницы: 265
Swan Analytical Instruments AMI INSPECTOR Hydrogen Operator'S Manual preview
AMI INSPECTOR Hydrogen
Бренд: Swan Analytical Instruments Страницы: 74
Simrad PI44 C Operator'S Manual preview
PI44 C
Бренд: Simrad Страницы: 322
Apera Instruments SX751 User Manual preview
SX751
Бренд: Apera Instruments Страницы: 32
Thermal Gas Systems HALOGUARD II Instruction Manual preview
HALOGUARD II
Бренд: Thermal Gas Systems Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды