manualshive.com logo in svg

Honeywell CM4, Техническое руководство

TDK-Lambda CM4 - надежный и эффективный источник питания для широкого спектра применений. Загружайте бесплатные руководства по использованию и приложения на manualshive.com, чтобы максимально эффективно использовать эту продукцию.

Поделиться
Скачать
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

7-7

3 – SET-UP MODE

3 – OUTPUT OPTIONS

1 – COM PORT

 

The display reads:

COM PROT VER 1

 

Other choices include:

COM PROT VER 2

COM PROT LONWORKS

and

COM PORT DISABLED

Refer  to  the  CM4  Serial  Communications  Protocol  Manual  (P/N 

1998M0020) for more information.

3.  After making a selection, press ENTER. The display reads:

COM PORT = 9600 BAUD

4.  Press  CURSOR  ARROW  RIGHT  to  advance  the  display  from 

1200, 2400, 4800, 9600, to 19200 baud.

5.  Press  ENTER  when  the  display  shows  the  desired  baud  rate. 

The display reads:

BAUD RATE UPDATED

 

The display reads:

INST ADDRESS 001

6.  Press  ENTER  after  selecting  the  desired  address.  A  unique 

address  must  be  assigned  to  each  CM4  sharing  an  RS  485 

bus.

The display then returns to the output options function.
Press RESET to return to the Set-Up Menu.

7.4.2 Optional Printer Port (3.3.2)

Purpose
Use the printer port function to enable the optional communication 

port and specify the baud rate for communication with the Network 

as either:

•  1200 baud
•  2400 baud
•  4800 baud
•  9600 baud
•  19200 baud

Instructions

1.  Press PROGRAM to exit Monitor Mode.
2.  From the 3–SET-UP MENU, choose the subfunction 3–OUTPUT 

OPTIONS, then 2–PRINTER PORT.

3 – SET-UP MODE

3 – OUTPUT OPTIONS

2 – PRINTER PORT

 

The display reads:

PRINTER PORT = ENABLE

3.  Press  CURSOR  ARROW  RIGHT  to  toggle  between  enabling 

and disabling the printer port.

4.  Press ENTER. The display reads:

PRINTER 9600 BAUD

5.  Press  CURSOR  ARROW  RIGHT  to  advance  the  display  from 

1200, to 2400, to 4800, to 9600, to 19,200 baud.

6.  Press  ENTER  when  the  display  shows  the  desired  baud  rate. 

珠海司福斯特科技有限公司

www.safedtech.com

Содержание CM4











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CM4

Keithley 486 Quick Reference Manual preview
486
Бренд: Keithley Страницы: 48
TaiDoc L1 Owner'S Manual preview
L1
Бренд: TaiDoc Страницы: 31
Idexx SediVue Dx User Manual preview
SediVue Dx
Бренд: Idexx Страницы: 6
IDEAL INDUSTRIES SignalTEK II Quick Reference Manual preview
SignalTEK II
Бренд: IDEAL INDUSTRIES Страницы: 10
M-system TR30 Instruction Manual preview
TR30
Бренд: M-system Страницы: 5
Weller WA2000 Instruction Manual preview
WA2000
Бренд: Weller Страницы: 9
Sanmenxia ZX400 Operation Manual preview
ZX400
Бренд: Sanmenxia Страницы: 17
SANKO SM-1100 Instruction Manual preview
SM-1100
Бренд: SANKO Страницы: 25
Samson 2162 Parts And Technical Service Manual preview
2162
Бренд: Samson Страницы: 2
Grundfos Vortex Flow Industry Instructions Manual preview
Vortex Flow Industry
Бренд: Grundfos Страницы: 16
Spacelabs 91390 Operation Manual preview
91390
Бренд: Spacelabs Страницы: 156
Parkside PMSHM 2 A1 Operation And Safety Notes preview
PMSHM 2 A1
Бренд: Parkside Страницы: 120
Seben 69003 Instruction Manual preview
69003
Бренд: Seben Страницы: 16
Armstrong Monitoring Corporation AMC-CD2 Instruction Manual preview
AMC-CD2
Бренд: Armstrong Monitoring Corporation Страницы: 12
Veeco Dektak 150 User Manual preview
Dektak 150
Бренд: Veeco Страницы: 349
GrainPro GPO2-AN Instruction Manual preview
GPO2-AN
Бренд: GrainPro Страницы: 7
Caen DT5740 Technical Information Manual preview
DT5740
Бренд: Caen Страницы: 50
SEAWARD Electronic Rigel 266 Plus Instruction Manual preview
Rigel 266 Plus
Бренд: SEAWARD Electronic Страницы: 57

Бренды по названию

Популярные бренды

Загрузить еще бренды