Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 64

Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 7

Section 1: General Information

1-3

Module Supervision Features

The communications module utilizes the following types of supervision and fault detection:

•

Network communication failure: In the event the AlarmNet network does not hear a
supervisory message from the module within a specified time (“Supervision” option),

AlarmNet notifies the central station of a communication failure.

•

Communication path failure: In the event the module detects a communication path

failure, the control panel can be notified of a trouble condition with the module after a

specified time has elapsed (“Notify Panel Of” option).

•

Fault output: Terminal 11 can serve as a fail-safe trigger for module fault conditions.

•

If used, the fault relay will trip when the following conditions occur: tamper, power loss,
low battery, battery charger fault, and loss of network connectivity.

(

Alarm reporting for

these conditions must be enabled.)
The fault relay will also trip if the module is not registered or if the module is remotely
disabled by AlarmNet.

•

Primary power loss and low battery reporting (“Pwr Loss Rpt”, “Low Bat Rpt” options).

•

Cover and optional back tamper condition reporting (“Tamper Rpt” option).

•

Internal antenna to provide additional security to the installation by making the device

tamper resistant.

Testing the System

Refer to the control panel installation instructions for procedures to test the entire system.

Compatibility

For a list of control panels that are compatible with this device, go to:

http://security.honeywell.com/hsc

.

From the Support & Resources tab, click MyWebTech. After logging on, enter the product
part number then click go. Under

Essential Docs

select

Compatibility Chart

.

Compatible receivers are:

•

MX8000

•

7810iR-ENT

•

Ademco 685

«
...
5
6
7
8
9
...
»

Содержание AlarmNet GSMBR

































































Отзывы:

Нет отзывов