Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 44

Страница: 44 / 64

GSMBR / iGSMBR Installation and Setup Guide

5-2

S – Searching

D – Registration Denied
R – Registered Roaming

? – Unknown Registration State

Press the [Space] key to go to the next screen.
Press the backspace [BS] key to go to the last screen.

Cntry Netw LAC
xxx xxx xxxxx

GSM Status Display Screen 2

Cntry – Country Code

Netw – Network Code

LAC – Local area code
Press the [Space] key to get to the next screen.

Press the backspace [BS] key to go to the previous field.

Cell BaseSt Chan
xxxxx x xxx

GSM Status Display Screen 3

Cell – Base Station ID
BaseSt – Base Station Antenna Sector

Chan – Control Channel in use

Press the [Space] key to go to the next screen.
Press the backspace [BS] key to go to the previous field.

Second Site RSSI
-xxxdbm

GSM Status Display Screen 4

Secondary GSM Site RSSI level in dBm.

Press the [Space] key to go to the GSM Status Display

Screen 1.
Press the backspace [BS] key to go to the previous field.

System Status Displays

The next seven displays make up a cycle of displays. Pressing the [Space] key advances you

to the next field in the cycle. Pressing the backspace [BS] key advances you to the last field
in the cycle (Line Voltage field).

[S]

ECP 67 TmPB Flt
xx 5 ++ OK

ECP Mode

Displays the zone and system fault status.

Press the [Space] key to go to the next field.

1234 67 TmPB Flt
5555 xx 5 ++ OK

4204 Emulation Mode

Displays the zone and system fault status.

Press the [Space] key to go to the next field.

12345678 TmPB Flt
5555555x 5 ++ OK

Two-4204 Emulation Mode

Displays the zone and system fault status.

Press the [Space] key to go to the next field.

1234567 TmPB Flt
5555555 5 ++ OK

Zone Trigger Mode

The status of the module can be viewed on the 7720P.

The status display includes:

Zone input status

(1234567)

– The numbers 1-7

represent the 7 mappings of the zone input, and follow

Honeywell's ADEMCO high-speed format codes:

=New Event

=Normal

=Not Enabled

– Tamper status follows high-speed format codes

above.

– Represents line voltage as follows:

=Power line voltage OK

–

= Power line voltage bad and reported

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 44 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: