Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 36

Страница: 36 / 64

GSMBR / iGSMBR Installation and Setup Guide

3-20

Programming for Zone Trigger, 4204 and Two-4204 Modes

PROMPTS

ZONE

TRIG.

4204/

2-4204 ENTRY

OPTIONS

DESCRIPTION

Restore Zn8 Y/N
(Y)_

2-
4204

only

[Y], [N]

Enables restore reporting for zone 8.

Delay Zn8 (secs)
(00)_

4204
only

[01-15]
[00] = no

delay

Defines the reporting delay in seconds for zone 8.

Prompts 70 thru 76 appear for the iGSMBR only.

Use DHCP Y/N
(Y)_

[Y], [N]

Dynamically allocates the IP addresses

(recommended); if [Y], then skip to Prompt 75:

"Enable Pwr Save". If [N], uses fixed IP
addresses.

NIC IP Address:
255.255.255.255_

12 digit:

xxx.xxx.xxx.x
xx

Enter the 4-part address for this device. The 4
parts of the address must be separated by spaces

(displayed as periods in Review mode).

Subnet Mask:
255.255.255.255_

12 digit:

xxx.xxx.xxx.x
xx

Enter the 32-bit address mask used to indicate
the portion (bits) of the IP address that is being

used for the subnet address. The 4 parts of the

address must be separated by spaces (displayed
as periods in Review mode).

Gateway IP Addr:
255.255.255.255_

12 digit:

xxx.xxx.xxx.x
xx

[0.0.0.0.] =

not used

Enter the 4-part address assigned to the
Gateway. The 4 parts of the address must be

separated by spaces (displayed as periods in
Review mode).

DNS Serv IP Addr:
255.255.255.255_

12 digit:

xxx.xxx.xxx.x
xx

[0.0.0.0.] =
not used

Enter the 4-part IP address assigned to the DNS
(Domain Name System) server. The 4 parts of

the address must be separated by spaces

(displayed as periods in Review mode).

Enable Pwr Save
(Y)_

[Y], [N]

For 24 hour Battery Backup requirement, this
feature must be enabled, or the unit must be

routers or switches disable this option.

IP Connection
(Present)_

Present
Auto Detect

Press the [space] key to toggle between the

options. Press [ENTER] to select the
configuration.
If “Present” is chosen, it is assumed that IP is
connected to the device. If it is not detected, a

Primary Comm Path Failure message will be

delivered after the programmed fault time
expires.
If “Auto Detect” is chosen, the device will always
try to use IP to communicate but it will not

generate a Primary Comm Path Failure unless it
previously detected the presence of IP. As soon

as the presence of IP is detected, a Primary

Comm Path Restore message is generated and
the value of IP Connectivity programming

parameter is changed from “Auto Detect” to

“Detected”.
From this point on, the software expects
connectivity. The auto detect logic will resume

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 36 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: