Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 64

Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 17

3-1

S E C T I O N 3

Programming

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

General Information

The GSMBR delivers alarm reports via GSM (Global System for Mobile) technology to an
AlarmNet central station. The iGSMBR delivers alarm reports via the Internet, and has the

additional capability to deliver alarm reports via GSM (Global System for Mobile) technology
when the Internet is not available.

The communications module requires an AlarmNet account. For new installations, please obtain the
account information from the central station prior to programming this module.

You can program the communications module by one of the following methods:

•

Using the AlarmNet Direct website

•

Using the 7720P Programming Tool

•

Using the control panel's programming mode (for panels that support this option) to
access the communication module's programming.

NOTE:

The prompts in this document reflect use of the 7720P Programming Tool.

Using the AlarmNet Direct Website

To program the module via the website (if you are already signed up for this service), go to:

https://services.alarmnet.com/AlarmNetDirect/

If you are not signed up for this service, click on “Dealer Sign-Up" and follow the

instructions.
Log in and follow the on-screen prompts.
Please have the following information available when programming the module:

•

Primary City ID (two-digit number), obtained from your monitoring station.

•

Primary Central Station ID (two-digit number), obtained from your monitoring station.

•

Primary Subscriber ID (four-digit number), obtained from your monitoring station.

•

Communications module MAC ID and MAC CRC number (located on the outside of box
and on label inside module).

After programming is complete, the module must be registered. Refer to

Section 4:

Registration

.

«
...
15
16
17
18
19
...
»

Содержание AlarmNet GSMBR

































































Отзывы:

Нет отзывов