Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 64

Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 47

6-1

S E C T I O N 6

Network Diagnostics

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

This section is for iGSMBR communication modules only.

Running Network Diagnostics

The network diagnostic process tests the integrity of the links between the communications

module and the various connection points of AlarmNet Control that are known as

"Redirectors" (Redirs or RDR).

To initiate the network diagnostics, press the [F] key on the 7720P Programming Tool.

NOTE:

The test is performed ONLY if a physical link is detected. If no physical link is

detected, the test is aborted and the following is displayed:

NO PHYSICAL LINK

If a physical link is detected, the diagnostics are performed. The following shows the
progression of the test:

Testing Redir 1

The first step of the test traces the connection to Redir 1 at

AlarmNet Control.

Testing Redir 2
Reached Gateway

A successful trace to Redir 1 is indicated here. Redir 2 is then
tested. See below for possible errors that may occur at this stage of

testing.

Redir 1
Service OK

The service at AlarmNet Control on Redir 1 is functioning. (See

below for possible errors that may occur at this stage of testing.)

Testing Redir 2

The first step of the test traces the connection to Redir 2 at
AlarmNet Control.

Redir 2
Service OK

The service at AlarmNet Control on Redir 2 is functioning. (See

below for possible errors that may occur at this stage of testing.)

Testing Redir 3

The first step of the test traces the connection to Redir 3 at
AlarmNet Control.

Redir 3
Service OK

The service at AlarmNet Control on Redir 3 is functioning. (See
below for possible errors that may occur at this stage of testing.)

«
...
45
46
47
48
49
...
»

Содержание AlarmNet GSMBR

































































Отзывы:

Нет отзывов