Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 31

Страница: 31 / 64

Section 3: Programming

3-15

Programming for Zone Trigger, 4204 and Two-4204 Modes

PROMPTS

ZONE

TRIG.

4204/

2-4204 ENTRY

OPTIONS

DESCRIPTION

Prompt 22 appears for the iGSMBR only.

IP Flt Time
(00 mins)_

[00-99]

In the event there is a loss of contact with the

network over the Ethernet connection, enter the
time delay (in minutes) before the

communica-

tions module

notifies the central station. IP

failure will always be sent to the central station
as Primary Communication Path Failure.

GSM Flt Time
(00 mins)_

[00-99]

In the event the module detects a communication
path failure, enter the time delay (in minutes)
before the

communications module

notifies the

central station. For an iGSMBR, a GSM failure

will always be sent to the central station as

Secondary Communication Path Failure. For a
GSMBR, a GSM failure will be sent to the

central station as a Primary Communication

Path Failure.

Prompt 24 appears for the iGSMBR only.

Notify Panel Of_
(Neither Fault)_

[Neither
fault]

[Both IP

and GSM
Faults]

If "Both IP and GSM Fault" is selected, the
device will only notify the control panel if both

communication paths fail, but will always send
notification of either failure to the central

station.

NOTE:

The fault relay output (if programmed)

will be triggered only if "Both IP and GSM

Faults" is selected.
Press the [Space] key to scroll through choices.

Flt Rel ON Y/N
(N)_

[Y], [N]

If enabled, the fault open collector output is

normally energized to ground, and de-energizes

(open circuit) in the event of a module fault. For
conditions that trip the fault relay refer to

Module Supervision Features

in Section 1.

Set to [Y] if fail-safe mode is desired.

See

Wiring for

Module Fault Relay

in Section 2.

Pwr Loss Rpt Y/N
(Y)_

[Y], [N]

Sends a primary power loss report to the central

station within 1-3 hours after its detection. A
restore report is sent within 1-3 hours after

power is restored.

Suggested Setting:

When using a transformer

and battery, set to "Y".

When using a LYNXR-I series control set to "N".

Low Bat Rpt Y/N
(Y)_

[Y], [N]

Sends a low battery report when a low battery

condition exists. A low battery restore is sent
when the condition clears.

Suggested Setting:

When using a transformer

and battery, set to "Y".

When using a LYNXR-I series control set to "N".

Tamper Rpt Y/N
(Y)_

[Y], [N]

Sends a tamper report when the module detects
a tamper condition. A tamper restore is

automatically sent when the tamper condition
clears.

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 31 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: