Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 23

Страница: 23 / 64

Section 3: Programming

3-7

Programming for ECP Mode

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

Prompt 27 appears for the iGSMBR only.

IP Flt Time
(00 mins)_

[00-99]

In the event there is a loss of contact with the network

over the Ethernet connection, enter the time delay (in
minutes) before the communications module notifies

the central station. IP failure will always be sent to the

central station as Primary Communication Path
Failure.

GSM Flt Time
(00 mins)_

[00-99]

In the event the module detects a communication path
failure, enter the time delay (in minutes) before the

communications module notifies the central station.
For an iGSMBR, a GSM failure will always be sent to

the central station as Secondary Communication Path

Failure. For a GSMBR, a GSM failure will be sent to
the central station as a Primary Communication Path

Failure.

Prompt 29 appears for the iGSMBR only.

Notify Panel Of_
(Neither Fault)

[Neither

fault]

[Both IP and
GSM Faults]

If "Both IP and GSM Fault" is selected, the device will
only notify the control panel if both communication

paths fail, but will always send notification of either

failure to the central station.

NOTE:

The fault relay output (if programmed) will be

triggered only if "Both IP and GSM Faults" is selected.
Press the [Space] key to scroll through choices.

Flt Rel ON Y/N
(N)_

[Y], [N]

If enabled, the fault open collector output is normally

energized to ground, and de-energizes (open circuit) in
the event of a module fault. For conditions that trip the

fault relay refer to

Module Supervision Features

Section 1.

Set to [Y] if fail-safe mode is desired.
See

Wiring for

Module Fault Relay

in Section 2.

Pwr Loss Rpt Y/N
(Y)_

[Y], [N]

Sends a primary power loss report to the central
station within 1-3 hours after its detection. A restore

report is sent within 1-3 hours after power is restored.

Suggested Setting:

When using a transformer and

battery, set to "Y".
When using a LYNXR-I series control set to "N".

Low Bat Rpt Y/N
(Y)_

[Y], [N]

Sends a low battery report when a low battery
condition exists. A low battery restore is sent when the

condition clears.

Suggested Setting:

When using a transformer and

battery, set to "Y".

When using a LYNXR-I series control set to "N".

Tamper Rpt Y/N
(Y)_

[Y], [N]

Sends a tamper report when the module detects a

tamper condition. A tamper restore is automatically
sent when the tamper condition clears.

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 23 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: