Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 45

Страница: 45 / 64

Section 5: Diagnostic Commands

5-3

= Power line voltage bad, not reported

(reporting window not expired)

= Power voltage restored, not yet reported

– Represents battery condition as follows:

= Battery voltage acceptable

–

= Battery voltage below 5.7V ±5%

Flt

– Represents radio faults:

= Normal ; No fault

= No network connectivity over IP and fault

time has expired

= No network connectivity over IP and fault

time has NOT yet expired.

= No network connectivity over GSM and

fault time has expired.

= No network connectivity over GSM and

fault time has NOT yet expired.

NOTE:

The 7720P will not operate if the power line

voltage is removed.

Bat NLd: x.xxV
Bat Ld: x.xxV

Battery Voltage Display

The voltage levels of the module's battery can be viewed

on the 7720P. The first line of the display shows the

voltage level of the battery with no load. The second
line of the display shows loaded battery voltage. An

asterisk (*) next to the voltage indicates that this is

below the accepted level.
Press the [Space] key to go to the next field.

Battery Charger
OK

Battery Charger Status Display

The status of the battery charger circuit can be viewed

on the 7720P. The status is either OK or NOT OK.

Press the [Space] key to go to the next field.

Line Voltage
xx.xxV

Line Voltage Display

The line voltage can be viewed on the 7720P. An
asterisk (*) next to the voltage indicates that this is

below the accepted level.

Press the [Space] key to go back to the System Status
Display.

[T]

Test Msg Sent

Test Alarm

Sends a Test alarm to AlarmNet. Functional for a

registered

module only. If the device is not registered, a

message is displayed indicating that the command
cannot be executed.

[X]

Reset CPU Y/N

Reset the module.

Pressing [N] returns to diagnostic mode (blank screen =

enter next command or escape).

Pressing [Y] resets the module (blank screen = reset
complete).

[

↑

]

(UP arrow)

Registering …

Registration

Registers a programmed module with AlarmNet

[

↓

]

(DN arrow)

Enter PIN#

Registration with PIN for Replacement Module

Registers a replacement module with AlarmNet, once

programmed, using the existing PIN #.

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 45 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: