Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 22

Страница: 22 / 64

GSMBR / iGSMBR Installation and Setup Guide

3-6

Programming for ECP Mode

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

RemoteAccess Y/N

(N)_

[Y], [N]

Press [Y] to allow the end user to access their system
via a website. Availability of this service is controlled

by the dealer via the web-based programming tool on
the AlarmNet Direct website.

Direct Wire Y/N
(N)_

[Y], [N]

Applies only to control panels that support Direct Wire.
Enables Direct Wire Downloading over IP.
If [N], and if Prompt 20: "Remote Access" is disabled,
skip to Prompt 23: "Supervision."

Keypad Address
(28)_

[01-30]

This address must be programmed if using either the
Remote Access feature of Direct Wire downloading.

Enter the appropriate device address.

NOTES:

1. This address must also be programmed as an alpha

keypad in the control panel or an AUI (advanced user

interface) type device, if a full enhanced graphic
interface to the system is desired and the control

panel supports it. DO NOT connect an actual keypad

(or any other device) assigned to this address.

2. If using a compatible LYNXR-I series control (when

available), this address must be set to "1."

This address must be unique from the "Device

Address" entered in Prompt 19.

Supervision
(24 Hours)_

•

30 Day

•

24 Hrs

•

None

The AlarmNet network must hear at least one
message from the module during this supervision

period; otherwise, AlarmNet notifies the central station

that a communication failure has occurred. (If the
supervision period is changed after registration, you

must re-register the module.)
Press the [Space] key to scroll through choices.

Prompts 24 and 25 appear for the iGSMBR only.

GSM Rollover Y/N
(Y)_

[Y] , [N]

If enabled, all messages (including AlarmNet network
supervisory messages) are sent over the GSM network

in the event of an Internet failure.
If disabled, all messages (except AlarmNet network

supervisory messages) are sent automatically over the
GSM network in the event of an Internet failure.

GSM 24Hr Tst Y/N
(N)_

[Y], [N]

If enabled, the iGSMBR module sends a message once
a day to verify module operation. A "secondary

communication path loss" message is generated if the
message is not successfully delivered.

Old Alarm Time
10 Minutes_

•

10 Minutes

•

15 Minutes

•

30 Minutes

•

1 Hour

•

2 Hours

•

4 Hours

•

8 Hours

•

12 Hours

•

24 Hours

Sets how long an undeliverable alarm is retried for

delivery to the central station. If the message is not
validated, it is retried until the old alarm time is

reached or the message is validated.
Press the [Space] key to scroll through choices.

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 22 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: