Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 29

Страница: 29 / 64

Section 3: Programming

3-13

Programming for Zone Trigger, 4204 and Two-4204 Modes

PROMPTS

ZONE

TRIG.

4204/

2-4204 ENTRY

OPTIONS

DESCRIPTION

Important Information Regarding Multi-Mode

In Zone Trigger mode, the options for Multi-Mode are "Enabled" or "Disabled." If enabled, whenever a zone on the

communication device is triggered, a corresponding email message is sent INSTEAD of normal central station

reports.
Cover tamper will send email event 8. All communication device system events (such as power loss, low battery, etc.)

are still sent to AlarmNet.

Events used to send email messages are defined on the Honeywell Total Connect web site, and must correspond to
events triggering the hardwired zones.

Multi-Mode (email notification) is intended as a convenience for the user, and does not replace Central Station
reporting of critical events (alarms, troubles, etc.).

Multi Mode
(Disabled)_

•

Enabled

•

Disabled

Enable if you want system events sent by email

to the user.
Disable for normal alarm processing.

Important Information Regarding Primary Account (Prompts 11-13)

Account information is provided by the central station administrator.

Primary City ID
(??)_

[01-99]

Enter the 2-digit primary city ID, 01-99
(decimal).

Primary CS ID
(??)

[01-FE]

Enter the 2-digit primary central station ID

number, 01-FE (HEX).

Primary Sub ID
(????)

[0001-9999]

Enter the 4-digit subscriber account number,

0001-9999 (decimal).

Device Address
(12)_

[01-15]

The module communicates with the control panel

as a 4204 relay module. Enter the appropriate

address. For VISTA-10P, and FA130CP Series

control panels, this must be address 12. For
other controls, see the control panel’s

Installation and Setup Guide.

NOTES:

1. The 4204 protocol limits address range to 01-

15. If using 2-4204 mode, the module assigns

the second 4204 to the next higher device
address (e.g., if entering address 12 for the

first 4204, then address 13 is automatically

assigned to the second 4204 module).
Program the control panel accordingly.

2. The device address(es) must be unique from

the "Keypad Address" entered in Prompt 17
and any other address used on the control

panel.

RemoteAccessY/N
(N)_

[Y], [N]

Press [Y] to allow the end user to access their
system via a website. Availability of this service
is controlled by the dealer via the web-based

programming tool on the AlarmNet Direct

website.

Direct Wire Y/N
(N)_

[Y], [N]

Applies only to control panels that support Direct

Wire.

Enables Direct Wire Downloading over IP.
If [N], and if Prompt 15: "Remote Access" is

disabled, skip to Prompt 18: "Supervision."

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 29 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: