Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 46

Страница: 46 / 64

GSMBR / iGSMBR Installation and Setup Guide

5-4

Force Upload of Configuration File to Server

Pressing [Y] will force the device to upload its entire
configuration file to the server.

Pressing [N] cancels the operation.

NOTE:

If the internet is not available, and the

module is not initialized, when you enter this

command, the following screen will be displayed:

Cannot Upload
Try Later! _

[0]

Force Server Update?
Y/N

Wait for the RSSI LEDs to light, indicating the

module has completed its initialization, and try again.

[ENTER]

Strt Prog Mode?
Y/N_

Enter Program Mode

Press [Y] to enter program mode; otherwise, press [N].

Internet Connectivity Displays (iGSMBR only)

[D]

Physical Link
Good/Bad

Network Diagnostics Display

Indicates whether the device has detected a physical
connection to the internet.

Press the [Space] key to go to the next field.

NIC IP Address
xxx.xxx.xxx.xxx

IP Information Display

Displays the IP address assigned to this device.
Press the [Space] key to go to the next field.

Subnet Mask
xxx.xxx.xxx.xxx

Displays the 32-bit address mask used to indicate the

portion (bits) of the IP address that is being used for

the subnet address.
Press the [Space] key to go to the next field.

Press the backspace [BS] key to go to the previous field.

Gateway IP Addr
xxx.xxx.xxx.xxx

Displays the IP address assigned to the Gateway.

Press the [Space] key to go to the next field.

Press the backspace [BS] key to go to the previous field.

DNS Serv IP
xxx.xxx.xxx.xxx

Displays the IP address assigned to the DNS (Domain

Name System) server.
Press the [Space] key to go to the next field.

Press the backspace [BS] key to go to the previous field.

Encryption Test

AES

Passed!

Performs a self-test of the AES encryption algorithm.

Press the [Space] key to go to the next field.
Press the backspace [BS] key to go to the previous field.

DHCP
OK

DHCP (Dynamic Host Configuration Protocol) indicates
server is performing satisfactorily.

Press the [Space] key to go to the Physical Link display.

[F]

Testing Gateway
Redir 1

Run Network Diagnostic Test

Performs a set of network diagnostics that tests the

integrity of the links between the communications
module and the various connection points (Redirs) to

AlarmNet. Refer to Section 6:

Network Diagnostics

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 46 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: