Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 28

Страница: 28 / 64

GSMBR / iGSMBR Installation and Setup Guide

3-12

Programming for Zone Trigger, 4204 and Two-4204 Modes

PROMPTS

ZONE

TRIG.

4204/

2-4204 ENTRY

OPTIONS

DESCRIPTION

Strt Prog Mode?
Y/N_

[Y], [N]

Enters programming mode.

Enter Password

[0-9, A-F, N,
S, T, X, Y]

If a password has been previously assigned, this
prompt appears.

Enter a 4-digit password (0-9, A-F, N, S, T, X, Y).

The next prompt appears.

Program Device?
Y/N_

[Y], [N]

To begin programming the module, press [Y] and
go to Prompt 9: "Device Mode."

To create a password if none has been assigned,
press [N] and go to Prompt 4: Create Password.

To change an existing password, press [N] and

go to Prompt 5: "Change Password."

Create Password?
Y/N_

[Y], [N]

Passwords can be used to protect account and
programming information.

If no password has been assigned, this prompt

appears after pressing [N] at the "Program
Device?" prompt.

If a password is desired, press [Y] and go to

Prompt 6: "Enter Password."

Change Password?

Y/N_

[Y], [N]

If a password has already been assigned, this

prompt appears after pressing [N] at the
"Program Device?" prompt.

Press [Y] if you want to change the password.

NOTE:

To clear an existing password, without

entering a new one, answer [Y] to the "Change
Password?" prompt, then press the [Enter] key

when prompted for the new password and its

confirmation.

Enter Password

[0-9, A-F, N,
S, T, X, Y]

This prompt is displayed if [Y] was pressed in
Prompt 4 or 5.

Enter a 4-digit password (0-9, A-F, N, S, T, X, Y).
Re-enter the password as confirmation.

If the password doesn't match the first entry, the
following is displayed followed by the "Exit Prog.

Mode?" prompt:

Verify Not OK
PSWD not created

Verify Password

[0-9, A-F, N,

S, T, X, Y]

Otherwise, the "Exit Prog. Mode?" prompt is
displayed directly.

Exit Prog. Mode?
Y/N_

[Y], [N]
[ESC]

Exits program mode.
Press [N] to go back to Prompt 3.

Press [ESC] to load factory defaults.

Refer to the

Exiting Programming Mode

paragraph in this section.

Device Mode
(ECP)_

•

ECP

•

Zone Trig.

•

4204 Emu

•

Two 4204s

Press the [Space] key to scroll through the modes

of operation.
Press [ENTER] to select mode.

See

Table 3

for ECP mode programming.

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 28 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: