manualshive.com logo in svg

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 3 / 64

Поделиться
Скачать
Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 3

i 

Table of Contents 

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

 

SECTION 1: General Information ........................................................................................................... 1-1

 

System Overview...................................................................................................................................... 1-1

 

Features.................................................................................................................................................... 1-1

 

Data Encryption ....................................................................................................................................... 1-1

 

Remote Services ....................................................................................................................................... 1-2

 

Modes of Operation .................................................................................................................................. 1-2

 

ECP Mode........................................................................................................................................... 1-2

 

Zone Trigger Mode............................................................................................................................. 1-2

 

4204 Mode and Two-4204 Mode ....................................................................................................... 1-2

 

Module Supervision Features.................................................................................................................. 1-3

 

Testing the System .................................................................................................................................. 1-3

 

Compatibility............................................................................................................................................ 1-3

 

Specifications............................................................................................................................................ 1-4

 

SECTION 2: Mounting and Wiring.......................................................................................................... 2-1

 

Select a Mounting Location ..................................................................................................................... 2-1

 

Determine the Signal Strength ........................................................................................................ 2-1

 

Mounting the Module............................................................................................................................... 2-2

 

Mounting Procedure .......................................................................................................................... 2-2

 

Wiring the Module ................................................................................................................................... 2-2

 

Wiring for ECP, 4204 and Two-4204 Modes.................................................................................... 2-2

 

Wiring for Zone Trigger Mode .......................................................................................................... 2-3

 

Wiring for Module Fault Relay......................................................................................................... 2-5

 

Ethernet Connections (iGSMBR model only) .................................................................................. 2-6

 

Power Connections and Options ............................................................................................................. 2-7

 

Powering the Communication Module (dedicated power source)................................................... 2-7

 

Powering the Communication Module (shared power source) ....................................................... 2-7

 

Backup Battery Connection .............................................................................................................. 2-8

 

Initial Power-Up Sequence ............................................................................................................... 2-8

 

SECTION 3: Programming........................................................................................................................ 3-1

 

General Information ................................................................................................................................ 3-1

 

Using the AlarmNet Direct Website ................................................................................................ 3-1

 

Using the 7720P Programming Tool ................................................................................................ 3-2

 

Using the Control Panel.................................................................................................................... 3-3

 

Programming Conventions ............................................................................................................... 3-3

 

Programming for ECP Mode ................................................................................................................... 3-3

 

ECP Status Codes............................................................................................................................ 3-10

 

Programming for Zone Trigger, 4204 and Two-4204 Emulation Modes ............................................ 3-10

 

Zone Trigger Mode........................................................................................................................... 3-10

 

4204 and Two-4204 Emulation Modes ........................................................................................... 3-10

 

4204 Emulation Mode Options................................................................................................. 3-11

 

Programming ................................................................................................................................... 3-11

 

Setting Factory Defaults........................................................................................................................ 3-21

 

Exiting the Programming Mode............................................................................................................ 3-21

 

 
 

Содержание AlarmNet GSMBR

































































Отзывы:

Нет отзывов