Honeywell AlarmNet GSMBR Скачать руководство пользователя страница 30

Страница: 30 / 64

GSMBR / iGSMBR Installation and Setup Guide

3-14

Programming for Zone Trigger, 4204 and Two-4204 Modes

PROMPTS

ZONE

TRIG.

4204/

2-4204 ENTRY

OPTIONS

DESCRIPTION

Keypad Address
(28)_

[01-30]

This address must be programmed if using either
the Remote Access feature or Direct Wire

downloading. Enter the appropriate device
address.

NOTES:

1. This address must also be programmed as an

alpha keypad in the control panel or an AUI

(Advanced User Interface) type device, if a full

enhanced graphic interface to the system is
desired and the control panel supports it. DO

NOT connect an actual keypad (or any other

device) assigned to this address.

2. If using a compatible LYNXR-I series control

(when available), this address must be set to

"1."

3. This address must be unique from the "Device

Address" entered in Prompt 14, and cannot

equal that device address plus 1 (one) if using
2-4204 mode.

Supervision
(24 Hours)_

•

30 Day

•

24 Hrs

•

None

The AlarmNet network must hear at least one

supervisory message from the module during
this supervision period; otherwise, AlarmNet

notifies the central station that a communication

failure has occurred. (If the supervision period is
changed after registration, you must re-register

the module.)

Press the [Space] key to scroll through choices.

Prompts 19 and 20 appear for the iGSMBR only.

GSM Rollover Y/N
(Y)_

[Y], [N]

If enabled, all messages (including AlarmNet
network supervisory messages) are sent over the

GSM network in the event of an Internet failure.
If disabled, all messages (except AlarmNet

network supervisory messages) are sent

automatically over the GSM network in the

event of an Internet failure.

GSM 24Hr Tst Y/N
(N)_

[Y],

[N] If enabled, the

communications module

sends

a message once a day to verify module operation.
A "secondary communication path loss" message

is generated if the message is not successfully

delivered.

Old Alarm Time
10 Minutes_

•

10 Min

•

4 Hours

•

15 Min

•

30 Min

•

1 Hr

•

2 Hrs

•

4 Hrs

•

8 Hrs

•

12 Hrs

•

24 Hrs

Sets how long an undeliverable alarm is retried
for delivery to the central station. If the message

is not validated, it is retried until the old alarm
time is reached or the message is validated.

Press the [Space] key to scroll through choices.

Содержание AlarmNet GSMBR

































































Результаты поиска

Содержание AlarmNet GSMBR

Отзывы:

Honeywell AlarmNet GSMBR, Инструкция по установке и настройке, Страница: 30 / 64

Результаты поиска

Содержание AlarmNet GSMBR

Отзывы: