hilscher NANL-B500G-RE Скачать руководство пользователя

Страница: 77 / 90

LEDs

77/90

LED

Color

State

Meaning

Front side NANL-B500G-RE - RJ45 Ethernet sockets Ch0 and Ch1, TAP A and TAP B

LINK /
RJ45

Ch0

to Ch3

green

A connection to the Ethernet exists

off

Off

The device has no connection to the Ethernet

RX / RJ45

Ch0 to
Ch3

yellow

Flashing cyclic at
2.5 Hz / On

The device receives Ethernet frames

Table 18: LEDs NANL-B500G-RE (front side), Interactive operating mode and Autonomous
operating mode

Indicator states

Definition

Single Flash

The indicator shows one short flash followed by an off phase.

The interval period for the flash when triggering a GPIO event is 100 ms.

Flashing cyclic
at 1 Hz

The indicator turns on and off phase with a frequency of 1 Hz:
on for 500 ms followed by off for 500 ms.

Flashing cyclic
at 1 Hz
(green/orange)

The display is switched on in green or orange phases, alternating with a frequency of 1 Hz:
Green On for 500 ms followed by Orange On for 500 ms.

Flashing cyclic
at 2.5 Hz

The indicator turns on and off phase with a frequency of 2.5 Hz:
On for 200 ms followed by off for 200 ms.

Flashing cyclic
at 5 Hz

The indicator turns on and off with a frequency of 5 Hz:
“on” for 100 ms, followed by “off” for 100 ms.

Flashing cyclic green
at 5 Hz (additionally
orange flash)

The display turns on and off in phases, with a frequency of 5 Hz:
Green On for 100 ms followed by Off for 100 ms; additionally a flash in orange appears every
500 ms.

Single Flash

The indicator shows one short flash followed by an off phase.
The interval period for the flash when triggering a GPIO event is 100 ms.

Table 19: Indicator states

Содержание NANL-B500G-RE



























































































Результаты поиска

Содержание NANL-B500G-RE

Отзывы:

Похожие инструкции для NANL-B500G-RE

Бренды по названию

Популярные бренды

hilscher NANL-B500G-RE, Руководство пользователя

Результаты поиска

Содержание NANL-B500G-RE

Отзывы:

Похожие инструкции для NANL-B500G-RE

Бренды по названию

Популярные бренды