HIKVISION Pyronix EURO 280 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 72

HIKVISION Pyronix EURO 280 Скачать руководство пользователя страница 69

Page | 69

POWER SUPPLY PROBLEMS

Fault

Description

Solution

Battery
Fault xxx

Battery Fuse failed,
OR Battery not present,

OR Battery volts low

Note: This indication should be expected
during recharge after a mains failure.

The top line displays ‘Control Panel’ if it is a fault
on the endstation, if the Battery fault is on a
ZEM/OPM ‘xxx’ will show the device type and the
top line the location text if entered, if not it shows
xxx-nn where nn is the address of the ZEM/OPM.

Bat Test Fail

XXX

Battery Load Test has

failed

Only displays if option selected.
Battery uncharged or capacity below
specification may need replacing. Same method

as showing the device as battery fault.

Bat Critical
XXX

Battery being powered
down

Protects battery from deep discharge damage
during extended mains failure. Same method as

showing the device as battery fault.

Note: System is now powered down

Mains Fail
xxx

Mains supply failed

System detects mains frequency out of

specification, as well as voltage.

Same method

as showing the device as battery fault.

Note:

'AC FAIL' timer operative

Fuse Fault x

Fuse identified failed,
OR Output protected by
fuse drawing excessive

current

Resolve the cause of the fuse fault and press
the E-Fuse reset button.

Low Volts
xxx

Power supply volts low

Battery volts below normal 'battery fault' level
during mains failure. Same method as showing

the device as battery fault

DETECTION FAULTS

Fault

Description

Solution

Control

Panel SAB
Tamper

Tamper fault detected on

connection from SAB

Terminal BT should be at or near 0v.
If not, is SAB Tamper switch closed?
Check Fuse F2 intact, and connections to SAB.

Case

Tamper XXX

Case tamper switch open

Secure switch closed. Same method of showing

the device as battery fault.

WD Fault
(Warning

device
Fault)

Low battery on grade 3
sounder cable fault.

Check and replace the battery in the bell. Check
the cable for high resistance.

«
...
67
68
69
70
71
...
»

Содержание Pyronix EURO 280









































































Отзывы:

Нет отзывов